Search results

  1. N

    What kind of oil should I use

    Yes You are correct ! My Bad ! I have a 2000 and just thought would be same. I reread the Model Number !
  2. N

    What kind of oil should I use

    I have a 2000 Johnson 60 HP Two stroke. This oil does not clog up my carbs as bad as other oil. I get this oil at ACADEMY. Its the only place I can find it.
  3. N

    2ND TIME REPLACING TRANSOM

    I have a 1986 Starcraft FM 160. I replaced the Transom back in August, 2012. It is rotten again. Back in 2012, I used regular plywood with waterproof glue. I think was BX grade but not positive of that number. I do know not to use Pressure Treated on this aluminum boat. I had to use a double...
  4. N

    2000 60 HP Johnson cranks fine then cuts off

    I will check squeezing the primer bulb tomorrow to see if that helps. I don't remember if I tried that when I was checking things Monday. Thanks. I will let you know if helps.
  5. N

    2000 60 HP Johnson cranks fine then cuts off

    I have never had this problem with my old Johnson 60 HP 2 stroke. It usually cranks right up no matter how long it sits. I have always run Non-Ethanol gasoline with Johnson outboard oil mixed at 50:1 I can choke it and cranks right up. Runs for 2 maybe 3 seconds and cuts off. I can choke it and...
  6. N

    Water Pump

    1980 model 60 HP Johnson. Last year I installed a new Water Pump Kit. Never was satisfied with the pressure I got afterwards. Has been sitting for months now and again not pumping water. Cleaned dirt dauber dirt from outlet hose and can blow thru it now. Is there anywhere else that dirt daubers...
  7. N

    Johnson 60 HP Shift Rod Adjustment

    I have a 2000 Model Johnson 60 HP. I reinstalled the lower unit after water pump replacement. When I start engine in neutral position, the propeller is in reverse. Do I need to turn shift rod to the lower unit clockwise or counter-clockwise to get back in neutral. Got my head spinning on this...
  8. N

    2000 Johnson 60 HP No Water out sight tube

    I installed a new water pump kit about a year ago. I noticed at that time it was slow about picking up water and pressure looked weaker than normal. Boat has been sitting for about 6 months and cranked it the other day and not pumping water. Have already checked tube for insect problem and it is...
  9. N

    Transducer Placement for a Hummingbird 898

    Today I purchased a Hummingbird 898 side imaging and just wanted to check on here about the placement of the transducer. The instructions say 1/8" to 1/4" below the transom to the face. Does anyone out there have experience with one of these to tell me that is fairly close to the right...
  10. N

    Hummingbird Side Imaging?

    Does anyone have any opinions on the Side Imaging fish finders? They are a little costly and was wondering if they work that great. Would love to hear from anyone that has one on their boat. Thanks
  11. N

    Stainless Prop or not?

    I have a 16 ft starcraft with a 60 horse Johnson. Would it benefit me to replace the factory prop with a stainless prop of the same size and pitch? Thanks
  12. N

    Gas:oil ratio for 2000 model Johnson 60?

    I have a 2000 model 60 hp johnson. It is in excellent mechanical condition and would like to know the best ration for gas:oil. I have been running on 100:1 since it was new and was just wondering if I should stay the same or maybe drop to 50:1. thanks for any and all input.
  13. N

    What made epoxy do this?

    Hey everyone. I am in the process of replacing my Starcraft transom. I have applied two coats of epoxy from US Composites with a 3 to 1 ratio. I waited 24 hours between each coat, in fact 48 hours between each coat because I applied to one side, let it dry 24 then flipped it over to do the other...
  14. N

    To Sand or not to Sand?

    I am in the process of replacing the transom in my Starcraft FM160. I already have my new transom cut out, holes drilled and first coat of epoxy #635 from US Composites went on today. Can someone tell me if I need to sand before I apply the second coat of epoxy? If so, what grit would be best...
  15. N

    Starcraft Transom Replacement

    I have a 1985 Starcraft FM160. I am in the process of removing the transom for replacement. Can someone tell me if I need to remove the Splashwell to gain access to the side bolts in the transom or can I simply trim away the foam flotation in the corners to reach in to the nuts on the inside? I...
  16. N

    85 Starcraft FM160 Transom Replacement help

    I have a 1985 Starcraft FM160. I am in the process of replacing my transom and have a question about the side bolts on the transom. I have removed everything except for the side bolts. I have foam flotation in the corners behind the corner plates. I am assuming I can just trim the top back...
  17. N

    60 HP Johnson steering cable removal

    I am in the process of replacing the transom on my Starcraft. I have disconnected all motor connections except the steering cable. Can someone tell me if I only have to remove the big nut on the right side of the motor around the steering cable, which goes back to the steering wheel. I have...
Top