Search results

  1. D

    Delco est conversion issues

    I. Just installed a Delco EST I place of my TB4. The issue I have is I'm only getting 9 degrees advance out if the distributor. Base is set at 10 total timing is 19 degrees @ 2400 rpm. Any suggestions ? I have checked the voltage and it's @ 12 to the distributor.
  2. D

    Thunderbolt IV issues

    I have a merc 260 with a thunderbolt IV . I have had 2 used advance modules go bad a new one is $500.00 has anyone tried the MSD ready to run distrubutor?
  3. D

    Merc 260 closed cooling question

    I have a 79 merc 260 with a San Juan cooling kit on it including the exhaust manifolds. My question is it pulls water from the alpha 1 impeller pump only. The original drive was pre alpha . The boat has been family owned since 81 and not changed. When I got it I put the alpha drive on and all...
  4. D

    Log style exhaust conversion question

    I have a '79 260 merc, I'm going to convert to center rise this fall. I have seen kits from GLM , BARR and Sierra all at diffract prices. I have read lots of bad on GLM . Is this true ?? Any real world experience ? The boat has a closed cooling system and lives in the salt. I do not want to...
  5. D

    Broken zinc trim tab

    I have broken 2 trim tab zincs in the last 2 months. Alpha one gen one. I have 1 inch clearance to the prop. Could the prop be creating a harmonic?
  6. D

    Shifting and high idle issue

    I have a Merc 260 with and alpha 1 gen 1 drive. The boat was running a bit warm 190-200 so I removed the lower unit and replaced the impeller and found a double gasket from the shop that rebuilt the drive last year. Had the heat exchanger cleaned and while I was installing the lower unit it was...
  7. D

    I did it!!!

    Merc 260 exhaust shutter replacement. Old style 3 piece Y pipe I replaced the shutters without removing the engine. I had to make some tools but 4 hours and I'm done.
  8. D

    Exhaust shutter question

    I am collecting parts for my center rise conversion. Does anyone know if its possible to adapt the exhaust shutters frm the bottom of the y pipe to the top for easier service?
  9. D

    Another closed cooling question

    I have a 260 with a San Juan cooling system . Currently I have log style manifolds and the boat came with center rise manifolds in a box. My question is when I change to the center rise do I need a different t stat housing? I have read a couple posts that you need to change so the engine cools...
  10. D

    Engine temp ??

    We went shrimping the other day and ran out an hour or so @ 3800 rpm the temp was running 190. Is this an issue ? Total timing is at 34 deg. If I back down to 3300 rpm it drops to 170. . For the boat it's a 79 sun dancer 24' with a 260. Closed cooling system that pulls sea water from the drive...
  11. D

    thunderbolt ivnition question

    I need to replace the connector yo my TB4 but the part number is discontinued! Any ideas??
  12. D

    odd noise question

    I just installed a new merc 260 engine and alpha 1gimball housing and new drive. I am new to boats so this may be normal. I have good alignment to the drive coupler . When the engine is idling I can hear a slight rattle sound from the coupler area, it does not change when I put the drive in...
  13. D

    More help needed please Pre alpha to Alpha

    I have or had a mercruised 260 pre alpha. the new drive and gimbal housing are alpha 1 gen 1. the inner transom plate is pre Alpha. My question is do I have to change the Y pipe to Alpha or will the old 3 piece Y pipe bolt up not using the center bolt. Will it seal and be reliable? Or do I need...
  14. D

    alpha 1 gen 1? How much HP will it take

    I am new to boats but not to cars and gears. I have a 24' Searay with a mercruiser 260. The engine has been worked on ..Dyno reasults later for low end so I can cruise @ 3K nicely. My question is,,,How much will the drive take? it is an alpha 1 gen 1 with new merc parts and a 1.5 ratio. My...
  15. D

    '79 SeaRay Sundancer restoration help needed

    I am restoring a '79 Searay sundance given to me by a family menber to bring back to life. The back half is rotten and now gutted. we are replacing the transom wood and engine mounts, stringers along the gas tank, bulkeds. My question for the boat community is, Do I need to replace the 3/4...
Top