Search results

  1. 9

    spindle/ hub seal tolerance

    Hello, what is the tolerance or overlap in thousandths of the seal to the spindle diameter? thanks jim
  2. 9

    oil filter part number

    Hi, Does anyone have a oil filter number for a mercruiser 454 mag 1990 vintage thanks jim
  3. 9

    hub dust cap

    what I noticed was that the new bearing caps i installed were stamped with a good tolerance to lock them in but once I removed them the diameter was compressed causing a lack of tight fit when wanting to replace. Im thinking the caps are a cheap, thin chinese POS.
  4. 9

    hub dust cap

    actually I had installed new solid zinc coated caps, popped them off for a periodic inspection and the next trip out I noticed 1 had come offand a 2nd was ready to fall off as well. So Im just determining the best way forward without losing more caps going down the road.
  5. 9

    hub dust cap

    so is this cap acceptable to use with a spindle that doesnt have a zerk?
  6. 9

    hub dust cap

    I need to replace my hub dust caps and want to go to the rubber plug center style for periodic inspections but wanted the audiences review of this style cap vs the standard solid cap with no rubber plug in the center. The current caps wont stay in place after i pulled them off for an inspection...
  7. 9

    which caulking is acceptable

    Hi. when I go to reinstall screws to attach a bracket on the outter face of my transom on my fiberglass boat which of these caulking choices is best to leak seal butyl rtv silicone marine silicone thanks jim
  8. 9

    trim tab hose repair

    I see that hose connections are being made with this crimp ring along with a new cylinder. I have these rings but wonder if you guys feel skeptical of this type of connection
  9. 9

    trim tab hose repair

    sounds like its cheaper to buy new cylinder with hose already attached
  10. 9

    trim tab hose repair

    hi, I need to replace a hose on 1of my trim tabs. Im using a boat leveler pump but unsure how to disconnect the hose at the tab. There seems to be a sleeve crimped over the hase at the cylinder. Any ideas? thanks jim
  11. 9

    wheel bearing seals

    thanks all for the replies
  12. 9

    wheel bearing seals

    Hello, Is it possible or just not recommended to reuse a wheel bearing (back side of hub)seal in order to access the bearing on a boat trailer. Not sure if there is a tool that safely removes a seal without oblong Ing or deforming it thanks jim
  13. 9

    transducer mounting

    i have fiberglass, thanks everyone
  14. 9

    transducer mounting

    Hi, im looking for a transducer that mounts in the hull rather than outside on stern. Are there such available? thanks jim
  15. 9

    oar lock bushings

    Solved; i took a 1" dia delron rod and ran it through the lathe for that perfect fit
  16. 9

    oar lock bushings

    Hello, does anyone know of a source for nylon oar locks that are 1/2" ID x 3/4" OD. I can only find 5/8" OD
  17. 9

    which wheel bearing cap

    my initial thought was that if i went with the cap with a rubber face it would be quicker to verify that a seal has not failed and let water past into the bearings.I seem to have that problem with my tandem trailer
  18. 9

    which wheel bearing cap

    Hi, I need to replace (4) wheel bearing caps on the boat trailer. I am wondering if the bearing caps with rubber center work when submerged or is it just an unnecessary risk. Otherwise I guess the bearing buddy is just what to buy. Any input? thanks jim
  19. 9

    trailer tires

    Ended up getting D rating with new rims in a kenda radial, just to cya on the weight. thanks for all your input
  20. 9

    trailer tires

    hello, My question is about trailer tire ratings, and choice. I used to run the nanco bias d rated tires (14"-75) on a tandem trailer, but I slowly went to a radial tire by tire.The radial wears much better. Unfortunately they are a c rating. The boat weighs 4400 lb approx loaded and Im...
Top