Search results

  1. C

    OMC Tools For Yamaha??

    Well I did aquire some special OMC tools for my Old E-rude that I replaced with a Yamaha 90.<br />Sorry I am not selling any, tools I buy and keep!<br /><br />I guess some may have uses as Yamaha tools too?<br /><br />OMC Connecting Rod alignment Tool?? NOPE This was a very expensive tool that...
  2. C

    Trim Gauges 2001 or Prior? 2-3 wire?

    Got all my gauges wired on new Yamaha 2004 90 2S.<br />Left trim gauge for last. Teleflex has two Yamaha gauges a three wire and two wire gauge. Both have three posts on the gauges, The newer 2001+ gauges are supposed to be "two wire" I am confused by this as the 2004 Yamaha 90 2S has three...
  3. C

    New Motor Trouble Out of The Box

    Now its not peanuts or monkeys but you may smile , take sidelong glances and say I told you so's ..Ok got my new 2004 Yamaha 90 2 stroke rigged on the Boston Whaler New 704 control Key switch..ready to gpo and when shifting into forward the prop will not lock up. turn it to the left and its...
  4. C

    Yamaha Tilt Lock for Trailering

    New 90 2S is set on the Whaler. Factory owners manual says not to use tilt lock when trailering.. motor can jump loose?? This tilt lock does not look as secure as the old OMC but if drawn down should it not be OK? Its the tilt lock and the hydralic holding the motor up.To tell the truth I dont...
  5. C

    New motors in Crate Whats There?

    Been busy rigging new controls for 2004 Yamaha 90-2S, yea I know should have had it one in a couple hours! but Rain and work and such..Anyway this new Yamaha has been in the back of my truck for three weeks. Wondering?<br />Are the cable ends in the crate? Got new ends for the 704 control in its...
  6. C

    Gauge Rigging/Tach/Hour Meter/Volt Meter 90 HP

    Posted here a week ago or so. rigging a new yamaha 90 on a Boston Whaler that had a 90 Evinrude. Took Rodbolts advise and bought a new Yamaha 704 top binical control, motor came with new 10 pin harness and keyswitch with horn. The 704 control takes care of the nutral switch and trim up and down...
  7. C

    Rigging 2004 Yamaha 90 former OMC Controls

    Just got a new 2004 Yamaha 90 2 stroke for my 17 Boston Whaler, It had a Evinrude 90. The boat has a Morse (teleflex Control) I have the following gauges and switches on the boat<br />Tach <br />Trim Gauge <br />Hour meter <br />Volt meter<br />I have a seperate trim switch that I rigged up...
  8. C

    90 V4 Rebuild ?Too Much damage? Pics.

    Well I posted in here about 5 months ago about rebuilding my 1988 Evinrude 90. 1800 hours plus. Finally I broke her down after a last ride 2 weeks ago. I figured on damage to pistons but found a spot on the crank I am concered about.. she may be too far gone. I can rebuild but it wont last...
  9. C

    New here.. Soon to rebuild Engine 90Hp 1988

    Been looking in here today and just joined. Been following Hotrods engine rebuild on his 115. Good Job hes done and he will get it all hashed out soon with the rotor problem! <br />I have a 88 Evinrude 90 Hp on my 17 ft Boston Whaler Montauk. Bought it new and now theres 1700 hours on it. 1400+...
Top