Search results

  1. kbert1171

    Syncing carbs?

    You're right. But it's no big deal, as I can send the tool back.
  2. kbert1171

    Syncing carbs?

    Doesn't the fuel get drawn into the cylinder by vacuum? And that tiny bit of vacuum is what is measured by the gauges. And I've seen several outboards that have small ports in the intake to hook up a gauge to tune the carbs. I simply assumed mine did as well.
  3. kbert1171

    Syncing carbs?

    I downloaded the manual. 1 5/8 turns out on the needle valve. So why don't the carbs need synced with the gauges like other outboards, including yamaha?
  4. kbert1171

    Syncing carbs?

    I ended up purchasing a sync gauge set. I'm sure I'll need it again sometime, and a few buddies have motorbikes, so it'll come in handy.
  5. kbert1171

    Carb tuning a 1986 Yamaha 50ELJ

    Where is a good starting point to set the needles before tuning the carbs after rebuilding them?
  6. kbert1171

    Syncing carbs?

    I only ever purchase factory parts, and I have the carb rebuild kit for this instance. I do not have the "factory" manual, only the Seloc. But I will find one before I start. My only problem will be the carb sync tool. I'll check with my local auto parts stores to see if they have one to loan...
  7. kbert1171

    Syncing carbs?

    My carbs need rebuilt on my 1986 Yamaha 50ELJ. Will they need synchronized after they are re-installed?
  8. kbert1171

    Water pump(impeller) question

    Purchased from Crowley Marine.
  9. kbert1171

    Water pump(impeller) question

    Changing the impeller in my 1986 Yamaha 50ELJ and the impeller is very difficult to get down the drives haft. The manual states that it should move smoothly up and down the driveshaft, but the one I removed and the new one was a bear to get off and the new one is a bear to get down the shaft...
  10. kbert1171

    Fuel pouring from hood?

    I unplugged it when I saw the leak, and it has stopped, but it's never done that before. Well, not after sitting for a couple days. It did last year when we lifted it when pulling the boat after fishing, but never while it sat in the driveway. I'm going to run some fuel system cleaner through...
  11. kbert1171

    Fuel pouring from hood?

    It's the original 6 gallon steel tank. Still ventless, though. I unplugged it as soon as I saw the fuel and its stopped. But it's never done that before in all the years I've owned it. It did last year when we lifted the motor when leaving the lake, but it hadn't done it this year.
  12. kbert1171

    Fuel pouring from hood?

    I just came home from work and noticed fuel dripping quite heavily from the hood of my Yamaha 50ELJ (1986). It used to do this when I lifted the motor when pulling it from the water, but hasn't yet this season. And then I come home to find it happening two days after we used the boat? What...
  13. kbert1171

    1986 yamaha 50ELJ prop size?

    Thank you very much, Mitchy2112. I really appreciate your help.
  14. kbert1171

    1986 yamaha 50ELJ prop size?

    Where can I find out what the stock porp was for my 1986 Yamaha 50ELJ? I need to replace it, but there are so many different options.
  15. kbert1171

    86 yamaha 50ELJ slipping??

    I was heading back to the launch today and had it full throttle, as most lakes we fish are no wake and I wanted to check top speed. Anyway, we were cruising along and the motor began over-reving, so I backed it down immediately to idle. It was running fine, water impeller working well, and full...
  16. kbert1171

    Pouring out fuel

    That's the only time I've noticed it. I'm going to run it for a few with the air box cover off and watch it. And as I lift it after shutting it down.
  17. kbert1171

    Pouring out fuel

    Thanks. I'll give it a try. Carbs were just gone through last year though.
  18. kbert1171

    Pouring out fuel

    I checked the lines and didn't see any cracks or breaks. I'll try running it while I check them.
Top