Search results

  1. S

    1992 evinrude 200xp tachometer issues

    I have a 1992 evinrude 200 xp I have replaced the stator,reg/rectifier,engine wiring harness and tachometer. my issue is the tach is jumping around. i have checked dva voltage to tach and im getting 10v dva when i rev the engine the tach settles in but at idle its jumpy . the dva voltage coming...
  2. S

    1992 Evinrude 200 xp

    I have a 1992 Evinrude 200 XP. What should the dva voltage be on yellow stator wires at idle and what should it be for the tach wire pulse signal. Also what should the voltage be coming off of red reg/rectifier wire I'm testing the charging system my tachometer is acting up it jumps around at...
  3. S

    35 amp regulator rectifier

    I have a 1992 Evinrude 200xp and I replaced the water cooled rectifier and developed a water leak at the gasket . What type of gasket sealer should I use to seal the gasket I know the book calls for Johnson Evinrude gasket sealing compound. I'm not sure if it was leaking at the gasket or bolt...
  4. S

    1992 evinrude 200xp wiring harness question

    1992 evinrude 200xp. what are the 3 small connectors the tan female and one black male plug and one black female plug in the picture i posted used for its directly above where the motor harness plugs in to the control harness. i replaced the harness and the vro has been deleted but i only...
  5. S

    1992 Evinrude 200 rectifier burned up

    I have a 1992 Evinrude 200 XP I just replaced the water cooled rectifier and stator had it running on muffs everything was good the tach was working again and the battery was charging like it should so I took it down the road to the lake and ran around for about 15 minutes and noticed smoke...
  6. S

    Evinrude 200 idle rpm

    I have a 1992 Evinrude 200xp. What should the idle rpm be on this motor it's running about 900 rpms .seems a little high and if so what's the best and correct way to adjust it.
  7. S

    Evinrude 200 reg/rec wiring

    Hi I have installed a new regulator rectifier on my 1992 Evinrude 200. The old regulator had a yellow/gray wire and a yellow wire. The new one has 2 yellow wires does it matter what terminal each yellow wire goes too or can it go either way. On the old one the yellow/gray went on the second...
  8. S

    Torque specs 35 amp regulator rectifier

    I need the torque specs for the regulator rectifier for the 35 amp charging system on a Evinrude 200xp motor ...thanks
  9. S

    installing lower unit 1992 evinrude 200 xp

    When installing the lower unit should the shift rod be engaged or disengaged. when i pull it up it engages the propeller im just wondering if theres a certain way to make it easier to get the linkage bolt in . also do the controls need to be in nuetral foward or reverse the book said to put in...
  10. S

    shift linkage bolt size

    what size is the bolt holding the shift linkage rod on a 1992 evinrude 200 xp . im servicing the water pump and need to remove the lower unit. thanks
  11. S

    gear oil capacity in lower unit

    how much gear oil does a 1992 evinrude 200 hp xp hold
  12. S

    35 amp charging system

    i have a 1992 200hp xp evinrude outboard. the battery is not charging and the tach is not working i noticed some melted goo running down the block below the stator only on the front side of the motor. the motor still runs perfect just no tach and no charging of the battery would the melting...
  13. S

    taking on water

    I have a stratos 201 ski with evinrude 200 hp outboard ive noticed that im taking on water when i have people in the rear of the boat or someone is being pulled on a tube for the life of me i cant figure out where its coming in but every time i pull someone and then stop i have to bilge it out...
  14. S

    1992 evinrude 200 xp rectifier regulator check

    how do you test the rectifier on a 1992 evinrude 200 xp outboard engine my battery is not charging and the rpm gauge is acting up
  15. S

    1992 evinrude 200 xp choke solenoid

    primer choke solenoid is not working is there a fuse for this or do i need to start tracing the wiring and checking voltage the engine is a 1992 evinrude 200xp. im having to manually turn the lever on the solenoid to get it started . the battery needs charging so i cant do any voltage checks yet...
Top