Search results

  1. J

    Alpha 1 Gen 1 Upper Unit Hex Bolt Connecting Halves Broke Off

    For any future readers: Upon further reading on my welding failure for those reading this in the future, it seems the bolt is stainless (3/8 - 16 x 1 inch) and my flux core welding setup did not have appropriate wire to bond to the stainless.
  2. J

    Alpha 1 Gen 1 Upper Unit Hex Bolt Connecting Halves Broke Off

    All great tips. I did not do as planed. I got bold and attempted the welder. As stated, I'm not even a novice welder. Its my diy Achilles heel. I always took wood shop to make sailboat parts, lol. I got the nut welded on about 3 times, but twisted off each time. Went back to what I know...
  3. J

    Alpha 1 Gen 1 Upper Unit Hex Bolt Connecting Halves Broke Off

    Yeah, to all of the above. I do have a small harbor freight welder, but I must admit my skills are pretty deficient. I dont want to blast a hole in my upper if I can avoid it. Going to give it another torching, douse it in oil and walk away till the weekend with shattered hopes of wrapping it...
  4. J

    Alpha 1 Gen 1 Upper Unit Hex Bolt Connecting Halves Broke Off

    Greetings, Working on an alpha 1 gen 1 drive, and when I went to separate the halves, the hex bolt which connects two halves at the stern (hidden by anode) twisted right off. To be clear I'm not describing the captive bolt that connects the anode, but the one that goes up from the bottom to...
  5. J

    Shift Cable Adjustment

    I did it with the lower shift cable disconnected from the shift plate, and the cable pushed forward so the shift lever would line up. With cable disconnected from shift bracket I'm able to put the boat in and out of both gears by moving the cable the cable and rotating prop with my foot. I...
  6. J

    Shift Cable Adjustment

    Hmm, I'm not sure about visible threads? Where exactly am I looking for those? On the lower shift cable at the bracket? I believe the slide set screw is correct.
  7. J

    Shift Cable Adjustment

    Greetings all, I've got a 3.0LX with a Sterndrive Engineering drive on the back. I have been around the moon trying to get this thing to shift correctly. Just replaced shift bracket (upgraded to the bracket that mounts to the starboard side of the engine due to faulty / obsolete cut out from my...
  8. J

    Alpha 1 Gen 1 Lower Shift Cable Lash Specs?

    Roger, I found those instructions in an older post, along with the .pdf. I appreciate it. Was more wondering if there was a quick way to measure to determine if the cable was stretched or not. It's the middle of salmon season here, and hoping to get the boat back in the water ASAP so I can fill...
  9. J

    Alpha 1 Gen 1 Lower Shift Cable Lash Specs?

    Can anyone point me to the Lash Specs for the upper and lower shift cables on an Alpha 1 Gen 1? How much should the cable travel? My Equipment: I've got a pre-alpha transom bracket, with the transom mounted shift assembly and old spring / lever style shift interrupt behind a 3.0 LX motor...
  10. J

    MC-1 - Alpha 1 Gen 1 compatibility

    Thanks!
  11. J

    MC-1 - Alpha 1 Gen 1 compatibility

    Hello! Finally got my 3.0 up and running, and we smoked the out drive on the first big fishing trip since putting the motor back in. Opened it up, and it's been on its way out for a while. Rusted bearings, shot gears, the works. Probably my fault, but I digress. Currently running an old...
  12. J

    Valve Cover Breather?

    Huh, yeah you'd think they'd give you a hose barb or something on the dang valve cover. It's even tapered to assist blowing off. Not a great design, bad even. Looks like the earlier models have something like that, but I also need the fitting that anchors the throttle cable for the a Mercarb.
  13. J

    Valve Cover Breather?

    So the stock setup is just a hose? No fittings? That's what I'm really asking.
  14. J

    Valve Cover Breather?

    Yeah, I went through all of that. Doesn't seem to make much if a difference. Maybe Ill throw the timing light on it, but would adjusting the spark timing really do much to dampen blowby? Do I have the correct parts? Seems to run fine. 135-140 PSI in all cylinders. It does blow quite a bit of...
  15. J

    Valve Cover Breather?

    Got a 3.0 LX here, trying to get the breather connected to the flame arrestor correctly. Any tips? It came with a hose that just blows right off. The outlet is sloped, and there is no barb or anything, doesn't look normal. I bought a 90 degree elbow hoping that was is, but the one I got...
  16. J

    Mercruiser 3.0 Exhaust Riser Leak / Compatibility?

    I'm with you. Precise language matters. Especially in a forum like this where specific words refer to specific parts, which other users may very well go out and purchase. As I know from spending a couple days worth of paycheck on the wrong manifold, buying the wrong part sucks (though that was...
  17. J

    Mercruiser 3.0 Exhaust Riser Leak / Compatibility?

    Ahhh, and this one is just an elbow: Is this a learning moment? Is there a technical difference in these parts, or just nominal difference...
  18. J

    Mercruiser 3.0 Exhaust Riser Leak / Compatibility?

    Thanks, this helps quite a bit. I was getting confused by all of the names different websites are using for these parts, I'd say the manual wins. Seems Iboats is calling it an "elbow riser," lol...
  19. J

    Mercruiser 3.0 Exhaust Riser Leak / Compatibility?

    Actually, in hindsight, I think I was talking about the riser not the elbow? (EDIT: INCORRECT, again, see below.) Also, looking up the parts numbers, I see a C1 stamped 42673 with 4 riser studs. So... still not certain that's what I think it is, but should know shortly and will update this...
  20. J

    Mercruiser 3.0 Exhaust Riser Leak / Compatibility?

    Thanks man!
Top