Search results

  1. shiloh87

    engine just quits

    Oh ya every things fine, new iggy, carb, fuel line, filter, tank. I built the boat a couple yrs ago. If I hit rough water a couple good thumps it`ll quit. Start it back up head on if it gets bumpy it`l quit. once it quits, I do due diligence and every things fine(always have my tools and...
  2. shiloh87

    engine just quits

    Hello and Merry Chritsmas from the great not so white north, no snow :( Its been over a yr, most gremlins are sorted on this project, boats running great when running LOL Getting 45mph wot with just me. Back to the engine just quits, I`ve come to the conclusion that a short or other gremlin...
  3. shiloh87

    engine just quits

    Yesterday I fired up the engine and reset the timing, with the dedicated distributor ground and it ran fine for the time I was working on it, around 15min. On the #1 wire timing held fine at 4deg btdc and the advance was spot on. Moved to 180deg, #4 wire, timing was good but advance was erratic...
  4. shiloh87

    engine just quits

    Turned on key, engine off, and checked coil voltage immediately, 1-2v, waited a bit while the coil energized then got a reading of 9v, so that`s good.
  5. shiloh87

    engine just quits

    Ya, I thought it was low as well. Going to investigate that today. I`ve installed a dedicated ground as Chris suggested, from the breaker plate to a block ground. After I figure out the low voltage I`ll try to fire it up and see what I get. Thanx so far gents, fingers crossed.
  6. shiloh87

    engine just quits

    Makes sense, I`ll give that a try.
  7. shiloh87

    engine just quits

    Hello again, back with more 1984 470 issues. My last inquiry was, having trouble locking down the distributor. Figured that out and fixed it, no issues with that until today. Went out for a cruise today and after about 45min of cruise we stopped to have an little lunch break. After about an...
  8. shiloh87

    locking distributor down

    Took the assembly out this morning, inspected it, its all good, gasket was good. Cleaned everything, no oil residue, installed another new gasket, reinstalled, set timing, and locked it down to 20ft/lbs, maybe a little more, then went to the bay for a shake down, ran great, but I`ll definitely...
  9. shiloh87

    locking distributor down

    Yes, the pictured clamp is indeed the one on my distributor, and the gasket was replaced with the rebuild. All good advise gents, thanx, I will investigate all your suggestions and report back...... Again thanx Rick
  10. shiloh87

    locking distributor down

    No bend in this clamp, its a thick chunk of shaped steel or aluminum and really will go on one way with the milled recess that engages the distributor lip. Maybe it needs a lock washer, can`t find a diagram to confirm or deny this.
  11. shiloh87

    locking distributor down

    Hello all, I`m having issues keeping the timing set, no matter how tight(20 ft/lbs) I crank down on the distributor clamp bolt, it moves. Didn`t have this issue last season, just seems to be this yr. The engine is a reconditioned 1985 470, 20 hrs on it so far. When it`s set correct the boat runs...
  12. shiloh87

    Old mercury prop numbers

    found this after some searching and digging michigan wheel scm30, PM27 merc number A-48-28037A1 which is a 9.5x9 3 blade but could find no reference of any other 3 bladed props of different pitches. So basically in 1962 this engine had 4 prop options 3 of them being 2 bladders 10,11,12 pitch...
  13. shiloh87

    Old mercury prop numbers

    I have a 1962 25hp O/B, its 8 spline LH rotation, wondering if anyone here has a link to old merc prop numbers, the 2 blade that`s on it has # CW 630 on it, which I believe is prt# 48-28036 28036A1 Prop 9-3/4×11, found it on ebay Looking for a 3 blade 8 spline prop for it, I know they were made...
  14. shiloh87

    remote control for my old outboard

    Owen Sound Area
  15. shiloh87

    remote control for my old outboard

    I`m in mid western Ontario Canada. I`ve seen those round looking ones but no reference to what they are for.??
  16. shiloh87

    remote control for my old outboard

    The out board in question is a Mercury, sorry forgot to include that tidbit of info. Someone must know what to use.
  17. shiloh87

    remote control for my old outboard

    Looked and looked but can`t seem to find which side mount remote control was used for the 1962 250(25hp) outboard motor. Would like to acquire an original to keep my vintage set up, well vintage. Any help would be greatly appreciated. cheers
  18. shiloh87

    In the process of Sanding?

    Never tried it, but its pretty tough paint, I would imagine it`d work well. Do a test on a piece for scrap plywood to see how it works first.
  19. shiloh87

    3.0 hydraulic lifter rebuild oil fill amount

    assemble then oil
  20. shiloh87

    Fun times

    Glad you noticed and repaired the water pocket cover too... Most people miss that one. How about the small seal at the bottom of the drive shaft housing? (The one the lower drive shaft, from the gear housing, goes through) Alls good, After everything cooled down, I disassembled and thoroughly...
Top