Search results

  1. J

    temp sending unit

    i have a 1993 mariner mag 3 when the sending unit for the temp gauge is cold what should the resistance be. also both unit are disconnected and removed from the head and the horn will beep steady when i turn on the ing. thanks jim cav
  2. J

    lubalert module

    hello i have a 1993 mariner mag 3 there is a electronic module that controls the tempature gauge, overheat light, low oil light and buzzer. does anyone know where i could buy this and or part # and price. Thanks jim cav
  3. J

    overheat light

    Hello I have a 1993 mariner mag 3 150 hp, yesterday I was running the motor in the yard on the garden hose. after about 5 min of running the overheat lite came on and the beeper was on solid. I turn off the motor and let it cool down for and hour, but know when i turn the key to the on...
  4. J

    sierra filter

    i have a sierra fuel filer 18-7844 and i need to know what micron it is? thanks jim cav
  5. J

    teleflex steering question

    Am i in the right spot?
  6. J

    motor guide 772 beast

    i just bought a used 772 beast trolling motor, i am looking for a wiring diagram and some advice on the circuit board that is in the motor head.<br /><br />thanks <br />jim cav
  7. J

    gas gauge

    i checked the voltage at the fuel gauge on one side i get 12 volts and the other side i get 7.8 volt and the guage reads empty the neddle is below the empty mark. i am not sure if it is the gauge or the sending unit. i am thinking it is the gauge.
  8. J

    just recieved manuals

    i just got the manual set for 98 johnson / evinrude motors it cover from 50 hp 3 cylinders and up this is the year 98 if some one needs certian sections please let me know.<br /><br />thanks <br /><br />jim cav
  9. J

    fuel pump part # ?

    98 johnson 70hp model J70TLEC<br /><br />Going to replace vro unit with fuel pump anyon know the part # for just fuel pump<br /><br />Thanks Guys
  10. J

    still feeling stupid

    1998 70 hp johnson<br /><br />well i think i tried everything. i will start with the compression test 2 cylinders are 110 and one is 115 know this test was done right after the motor was run, it was warm know can i still get good readings with the cylinders screwed up some how. the major problem...
  11. J

    vro help

    is there an easy way to test the vro unit<br />98 johnson 70 hp
  12. J

    at my wits end

    well i fixed some problems but the one that still eludes me is i cant get the motor to idle correctly. I have a 98 johnson 70 hp model #j70tlec. Rebulit all 3 carbs. it will run but idles ruff at 1/2 or full throtal it run fine.<br />After running for a while i have to hop on the gas so it wont...
  13. J

    vro

    back again sorry to be a pain guys. i have 1998 johnson 70 does omc make a rebuild kit for the vro unit.
  14. J

    best place to buy parts

    i have a 98 johnson 70 i think i need a new vro pump because the spark plugs are always wet with gas and oil. i did rebuild the carbs according to the manual. seems to be running better but there is black sut comming from the exhust. can some let me know the best place to buy a vro pump on line.
  15. J

    need help i am lost

    1998 70 hp johnson runs ruff when idling will stall if you put it in gear, have to jump on gas so it wont stall seems to run good at high speed.<br />Checked the spark look good. I checked it with inline tester it lit. Sprayed carb cleaner in the carbs. it seem to want to stall when i was...
  16. J

    stalling when put in gear

    i have a 1998 70 hp johson outboard, when i start it idles ruff when you put it in gear it will stall at low rpms if you get on the gas it will run fine. i think it is running rich because i see black sut on the motor and ground when running it. <br /><br />thanks <br />jim cav
Top