Search results

  1. N

    Painting Prep for One part paint over gel coat

    Hi fellas I’m planning to paint my 19 foot bay boat for duck hunting. I’m thinking of going with a dark gray brightside interlux so that I can easily touch it up. I am also going to prime it with interlux. I want to make sure I put in good prep work on the hull before painting. What steps...
  2. N

    Motor cut out on me -- Johnson/Suzuki 2005 115hp 4 stroke

    Primer bulb was not firm - I was able to push fuel into the VST when priming
  3. N

    Motor cut out on me -- Johnson/Suzuki 2005 115hp 4 stroke

    great feedback here gents I actually did pump the primer bulb a few times but it didn’t seem to make a difference Not sure if the outboard is water cooled fuel cooler - I’m not sure what even is. Guess I’ll need to read up Fuel pump seems to be fine but I’ll look into the fuel pressure...
  4. N

    Motor cut out on me -- Johnson/Suzuki 2005 115hp 4 stroke

    I have a 2005 Johnson (Suzuki) 115hp 4 stroke with 540 hours Two weeks ago I was out on the boat and cranked the motor up after fishing a spot -- pushed the throttle down to get up on plane and the outboard bogged down - I came off the throttle for 10 seconds and then pushed it back down and...
  5. N

    Leaf Spring Shackle Question

    These are all valid point gents. I appreciate the insight here. Will call the manufacturer and talk with them as well. Maybe I need some beefier springs. I’m pretty positive the boat isn’t water soaked so I’m thinking the springs might be manufactured wrong
  6. N

    Leaf Spring Shackle Question

    Yea weight rating on spings is 2000 each 4000 total - bot should be wel under that…maybe the springs are crappy?
  7. N

    Keel Repair

    This brings up another question — I hate the bottom paint color….could I just paint over it with black bottom paint or would I need to strip the blue off first?
  8. N

    Keel Repair

    Thanks for the answer - it’s below the water line if not in plane. I’m curious though - why would I not be able to gel coat over epoxy + cabosil?
  9. N

    Keel Repair

    Scratched the keel putting the boat on the trailer in high winds. Two Questions I want to take the boat out tomorrow but started to think it might be a bad idea. What do you all think? Looking to repair this - I was thinking some cabosil and epoxy - will dremel it back a bit first, sand...
  10. N

    Leaf Spring Shackle Question

    Maycraft 1900 1900 lb hull 52 gallon tank - 3/4 full right now 2005 Johnson 115 4 stroke - approx - 335 lbs Springs are rated for 2000 each or 4000 total Manufacturer of boat works specifically with road king on this package (atleast what road king told me on the phone)
  11. N

    Leaf Spring Shackle Question

    Hahaha ignore the zip tie 😂 I also did the lights today and it there while fishing the wires Before they looked similar I just didn’t know if the shackle was supposed to be pushed toward the back or if there should be more clearance for the axel. The more I think about it - it’s perfectly fine 😂
  12. N

    Leaf Spring Shackle Question

    I just redid my springs on my road king w/ 1900 maycraft on it correct springs and gear according to road king. seems like the shackles are pointy towards the stern… also to my inexperienced eye it seems that there isn’t much axel clearance. would love to hear your thoughts. Hopefully it’s...
  13. N

    Wiring diagram, is it correct?

    Hi guys, I’ve spent the last hour trying to figure out the wiring for my 14 foot skiff. I’d like to have the switch panel in the stern (tiller drive) and the battery near the bow for weight distribution. Here is the best I could come up with. I am struggling to understand the smartest way to...
  14. N

    Adding strings to a boat without stringers

    Also if I put stringers in how should I go about a proper drainage system?
  15. N

    Adding strings to a boat without stringers

    Thanks for your feedback. The hull is made out of Chopper Gun fiberglass. The hull is actually a lot deeper than the picture makes it look. If I was going to go with just two stringers which groves would you recommend putting them in? Or should I just go for 3 stringers?
  16. N

    Adding strings to a boat without stringers

    Hi guys, I’ve got a 14 foot skiff/fiber glass Jon boat that I’ve been working on. I have a 25hp on it. I have taken it out a couple times and at higher speeds 20+ mph the hull will flex in the middle. My thought is if I put in a stringer or 3 it should solve for the problem. I wanted to post...
  17. N

    Low Compression Top Cylinder NS25C3

    I hear ya guys. I couldn’t find an OEM gasket they were all shipped from overseas…
  18. N

    Low Compression Top Cylinder NS25C3

    That makes sense -- how do I go about making them flat?
  19. N

    Low Compression Top Cylinder NS25C3

    Sounds good. I guess I couldn’t just spray some WD-40 in there?
  20. N

    Low Compression Top Cylinder NS25C3

    How should I put the oil through it now? Or do you mean once I put the head back on run a heavier oil ratio?
Top