Search results

  1. C

    furuno nmea connection????

    i have a furuno 6ool color fishfinder withe a six pin nmea cord i want to inter phase it with my raymarine c 80 unit any advise how to connect the 2 would be greatly appreciated. my goal is to have gps data on fishfinder also, thanx in advance! bill
  2. C

    yamaha ox66 250 fuel consumption

    hi, i have twinn 250 yami ox66 on my grady white marlin, i average about a mile per gallon according to my fuel management sytem this seems horrible 2 me, any ideas or is ths the norm? ( cruising speed approx 28 mph)
  3. C

    evinrude 9.5 recoil problems

    have a 1972 evinrude sportwinn, 9.5, cannot get the recoil on the starter to"recoil" spring looks fine, any ideas???
  4. C

    yamaha ox66 trim indicators

    just got my boat, have twin ox66's the gauges on the console show trim indicators. when adjusting the trim the indicators dont move. all other gauges work great, any ideas guys??
  5. C

    nmea connections???

    have a northstar 951 x and a furuno 600l fish finder, trying to interphase, anyone know correct wiring procedure?? have both cables! thanx in advance
  6. C

    johnson ocean runner overheating

    started my engine today, hot water commimg out of pisser, warning alarm indicated overheat, is this a costly repair , waht does it entail? thanx for your help
  7. C

    garmin 210 gps problems

    my 210 was turning on then powering off. now it wont even power up. cheked and replaced in line fuse, still no luck, nothing seems corroded on power cord. think its the cord or the unit itself???? thanx for looking, bill
  8. C

    evinrude 9.5 point adjustments

    i need to adjust the points to .20 on my 9.5 anyone know what type of tool to use so they are adjusted right? one seems to be greater gap than the other. thanx in advance for any help!!!
  9. C

    Johnson Ocean Runner 200 Warning Horn

    The warning horn goes off every 30 - 40 seconds. it suggests that motors are over heatin but they seem to be running fine , plenty of water going through. how to disconnect, becomming annoying.
  10. C

    evinrude 9.5 sportwinn

    my 9.5 is spitting salt water inside of the motor . its comming out right near the rear screw of the recoil unit. It has rusted up ! any ideas how to fix??? thanx
  11. C

    replace con rod on 7 hp arien sno blower

    do i have to take the piston housing off the motor to install a new rod?? any easy way?? thanx for your help!!
  12. C

    airens 7 hp snowblower flywheel stuck

    hi, bew the auto starter on blower. tokk apart found the fly wheel where u pull start it makes approx 1 1/2 turns and stops, go the other way and it stops again. any suggestions?? thanx, bill
  13. C

    9.5 EVINRUDE pops out of gear

    sometimes at almost full throttle, motor pops into nuetral, how do i adjust this to resolve the prob???<br />thanx bill
  14. C

    200 hp johnson ocean runner leaks when trimmed

    when i fully rim my motor (out of water) a film of either gas or oil pools on the water. cant see any leaks comming out of motor! any ideas? doesnt seem to effect motor! thanx for any advise!
  15. C

    purchase wick for 9.5 stator plate

    where would one buy the wick neccesssary for the stator plate on my 9.5 evinrude motor. any help would be appreciated. thanx bill
  16. C

    armature plate install 9.5 evinrude

    took off old armature plate from 72 9.5 evinrude,<br />inner circle is grooved on old plate, there is a grooved piece on the cam shaft. the new plate is smooth and will not fit correctly . should i try to remove grooved piece from shaft? don't want to screw up the shaft! thanx capnwill@comcast.net
Top