Search results

  1. M

    double head gasket?

    Anyone ever used to head gaskets to correct piston/head clearence when a low compression head gasket is unavailible???? does it work ok? 60 hp 2cyl
  2. M

    replacement wrist pin bearings

    My replacemnet wrist pin bearings look like they have way to much open area where there is no washer or bearing please look at attached picture. It is 1983 60hp 2 cyl.
  3. M

    impeller change

    Hi, Can you inspect the impeller without replcing it? Can you change just the impeller or do you need to buy the sevice kit? When is houding replacment nessisary? Thanks, Chris
  4. M

    Upper, center mains

    Hi, I am rebuilding the powerhead on my 83' 60 hp rude should the upper and center main be replaced with the rebuild they seem very expensive. What would be a good Check for them? Thanks, Chris
  5. M

    piston to cyl clearance

    I am rebuilding a 2cyl 60 hp and the machinest says i can just hone but i will be .003 over stock bore size which will put me at about .006 cyl to bore clearance is this acceptable or should i just bore? How long will the motor last and and what is the disadvantages I am buying new pitons...
  6. M

    BIA Bolt Pattern

    What year did mercury switch to the BIA bolt pattern for mounting holes on the transom? Thanks
  7. M

    rod cap alignment

    I have the hand sanded rods as descibed in the book is it difficult to obtain proper alignment? Thanks, Chris
  8. M

    reed valves

    Should you be able to see a little bit of light through the reed valves or should they be totaly closed?? THANKS, Chris
  9. M

    50 hp force

    Looking at used motor is this a good durable engine?? is a late 80's How well will it move a 750 pound 16 ft tri hull? Thanks, Chris
  10. M

    hydrofoil stabilizers

    Hi, do they really do anything? and is it worth it? Thanks, Chris
  11. M

    Freezing outboard

    Does anyone use antifreeze in an outboard for winterizing or are they ok if drained?
  12. M

    60 hp 2 cyl water in bottom cyl

    Hi I have a 1983 60hp with water in the bottom cyl I think it is a head gsket becouse I have only an outer exhaust cover gasket. Is there any other place for water to get in? Also gan the head gasket be done on the boat? Thanks
  13. M

    60 hp rude exhaust cover gasket 1 or 2

    I have a 1983 60hp 2cyl evinrude and need a exhaust cover gasket my repair manual shows an inner and an outer gasket in the diagram but napa cannot get the inner one they tell me they can only get the outer one and thats all that is listed. so does anybody know if there is only one or two...
  14. M

    steering drag adjustment?

    I have an 1983 60hp evinrude and was wondering if it is possible the increase the steering drag? I cannot find an adjustment screw if there is one could you guys point me in the right direction. Thanks, Chris
  15. M

    60hp evinrude exhaust cover gasket

    I have a 1983 60hp evinrude 2cyl that I have water getting in the bottom cyl I told it is probably the exhaust cover gasket as I have good compression. My question is, is it possible to change the gaskets with the powerhead on the motor becouse it looks like the bottom bolts will not come all...
  16. M

    80 Hp engine repair ( piston cyl question)

    I have a 1978 80 hp and need to know if one cyl can be oversized .015 while leaving the others standard. The cylinder in question is not drawing in any fuel I think becouse of low comp the bore is about .011 out of spec at the top of the cyl. That cyl had overheated on the previous owner and he...
  17. M

    Git ROT??

    Hi,<br />I recently purchased a 78 glastron which appears to have some rotton wood in the transom where the motor bolts on and a friend told me to use git rot. Has anyone used this product and what can yu tell me about it? also has anyone used seacast?<br />Thanks,<br />Chris
  18. M

    picture of throttle linkages 80hp

    hi <br />bought an engine and it came slightly disassembbled need a pic of the linkage where the throttle opens on the top of the carb and also the side of the engine where the levers and linkages are if anyone has one handy.<br />Thanks <br /><br />it it a 1978 80hp
  19. M

    78 80hp bearings

    I have recently purchased a 78 mercury 80hp 4 cyl and the previous owner had given up on it after doing a ring job and impeller and never being able to get it to idle. just before he gave up on it he took it to the shop and they gave him an $1100 estimate on replacing all electrical parts and a...
Top