Search results

  1. D

    Hydraulic Fittings

    I have a 93 18 ft ProCraft Bass Boat with a SeaStar I hydraulic steering system installed. I have noticed over the last few years it leaks a little so I started investigating. After further inspection, the hoses are being kinked from trimming the motor up to the tow position. With the motor in...
  2. D

    weird temp readings

    82 blackmax 200 on an 18 ft procraft bass boat. Sometimes warning buzzer goes off at 140 sometimes not my temp guage gets to 180. I have been reading a bit on here and wondering if the sensor might be bad. I have no beep at start up. Over the last 3 years I have replaced thermos water pump and...
  3. D

    Should my black max 200 pee strong all the time?

    Had to tow a guy in last week. At idle all temps were fine but moving very slow. I decided to try a little faster. @ 1200 rpms I began to overheat. I could shift into neutral run up to about 3000 rpms and get the motor to cool. He later told me that the stream got weaker as it got close to...
  4. D

    Cracked Lower Unit

    Last week my mechanic called to say my lower unit had a hairline crack in it and was gonna be hard to keep sealed. Long story short I bought a used one from him and I still have the old one. It has a low water pickup and was told by him that it was a "hi performance" unit. I took it to him for...
  5. D

    are my controls bad?

    I have a 93 procraft with a blackmax 200 few weeks ago went to lake and no forward everything was fine the last time out. After limping back to dock in reverse I thought simple adjustment and off I go. After some reading and talking to a local mechanic he determined by guess my controls were...
  6. D

    Control location

    I recently bought new controls for my 93 procraft bass boat. The old control base is square therefore the mounting base isn't much bigger than controls. The new control is more oval and larger than the old. Looks to me like I should build out the old location. Should I try to make a new bracket...
  7. D

    Hi Performance Lower Unit

    I was told that I have a high performance lower unit by my mechanic and needed to use hi performance lube. I do have a low water pickup is all I know. Where would serial number on the lower unit be. I need new water pump, base, etc. Does anyone sell the whole kit (Including the base)? Am I...
  8. D

    Gen II Controls

    I picked up 883709A02 off ebay, no manual. Anyone have a manual, picture, or can tell me where the shift cable hooks up?
  9. D

    Shift Cables

    I recently bought new controls on ebay and seller says I need to use Gen II mercury cables. My boat has teleflex CC17912. What is the difference between the Gen II cables and this one? Will a Gen II cable work on my 82 black max 200?
  10. D

    Quicksilver control box

    I have a 93 procraft 180sp that I suspect the control box is wore out. Will not click when put in forward. I am looking for a box on ebay and wondering which controls will work and which ones won't. I have an 82 blackmax 200 on the back. My kill switch is seperate from the box. The only wires in...
  11. D

    Shift control cable

    Friday I took my 93 procraft sp180 out for the first time of the year. Pulled away from the dock with the trolling motor shifted into forward and nothing reverse was fine but no forward. Back at home I could shift into forward manually so I pulled the cable. Now I am confused as to what cable...
  12. D

    Trouble out of the hole

    82 Mercury 200 on 18 ft ProCraft Bass Boat. 25P Prop. Hi Performance Lower Unit with low water pickup. Boat is rated for 675 lbs. I think When my brother and I are in the boat, (600 lbs.) with the livewell semi full The boat struggles to get out of the hole. He can lay on the front deck and it...
  13. D

    Lower unit Leaking

    82 Merc 200, Low Water pickup. I notice a small puddle of gear oil under lower unit, and an oil trail that seems to come from behind the prop. Prop shaft oil seal? Should I have the whole unit resealed? How much should I be looking at $?
  14. D

    Prop Damage

    I have a 25 P Quicksilver SS prop on an 82 Merc 200. My prop is very slightly nicked on some of the edges. Can I file these nicks out or would this be better done by a prop shop? There are no major nicks or bends mind you. TIA Mark
  15. D

    200 h.p won't idle

    I have been fighting now for 5 weeks to get my 82 200hp cool, not worrying about anything else. Now that the engine runs cool, I can tackle some of the other issues. When I am at home running on the tank, the engine idles smooth and about 750 RPM. When I go to the lake, the same, as soon as I...
  16. D

    too much prop?

    I have a 1993 Procraft Super 180 Bass Boat with an 82 200 hp Mercury on it. I believe I have a 25 pitch prop. WOT RPM's max at 5000. Is this too much prop for this boat?
  17. D

    Lower unit metal breaking

    I previously posted a long and drawn out deal about my 82 200 h.p overheating. This is the 3 time I have had the lower unit off. I back flushed from the Poppett and everything is fine. Here is what I think is the problem. I have a low water pickup, hose on the side that goes directly into the...
  18. D

    Poppet Carrier fell in block

    Today I was pulling the carrier out of the block on an 82 200 behind the poppet valve and ole fumble fingers here pushed it into the block.<br /><br />Please, Please, Please tell me I don't have to pull the Powerhead to get it out. I rooted around in there to see if I could find it and I can't...
  19. D

    82 model 200 cooling problems

    First of all, thanks for all the help everyone gives on this board. I am sure my local dealer would be very tired of me by now.<br /><br />First of all, I am very new to boating, but have mechanical sense, at least I think.<br /><br />I have a 93 Procraft Super 180 that I thought had a 93 or so...
  20. D

    Shift shaft alignment

    I just put a new water pump on my 82/84 200 merc. I want to make sure I have the shifta shaft lined up correctly before I have a big problem.<br /><br />In Forward, thd prop clicks clockwise and has resistance counter clockwise<br /><br />Neutral, prop spins freely<br /><br />In Reverese, the...
Top