Search results

  1. R

    02 Merc 40 2 stroke warning buzzer

    The warning buzzer is going off cold with the key on. Will still run wot. I think we got a bad sensor or short. Any help
  2. R

    1989 Johnson 120 no down tilt

    Yesterday I was installing my transom saver, I must have put too much pressure down. I raised it up to relieve some pressure and when I pressed the down button, nothing happened, no movement or sound. I tried all three switches. It will move upward fine. I think I must have blown a fuse or...
  3. R

    Boat loading difficulty.

    I just bought a1993 Cajun 168. When the fella that sold it to me took me out to test it out he had to fight to get the very nose of the boat over the front roller. He said we needed a lower drop hitch, I have a 02 f150 4x4, put on a 6" drop reciever. The ball is at a below average height now. We...
  4. R

    need a prop expert

    I have a 17' bass boat I just bought used. It has a 1989 Johnson 120. This is my third bass boat in the last 15yrs and I never had to do much with the props, they all really got up and went fine. The reason I think I may need a prop is because it appears to have the original alluminum prop...
  5. R

    1962 Evinrude 5.5 waterpump install question

    Several years back I picked up this little 5.5 at a yard sale along with a 1982 Johnson 9.9. I have been using the 9.9 for about five yrs. I just put the 5.5 in the shed. I just decided to see about getting it running. This thing looks like it has had about 20 trips on it. I don't think it has...
  6. R

    9.9 year model?

    I guess I need to go get an impeller. I looked at the tag, the serial # is e5597573 the model # was blank. I pulled the cowl and the silver plug hand the serial # plus the #J10RCNS. Any help? Thanks
  7. R

    9.9 waterpump

    I made some fuel sustem repairs to the motor. set it on a stand with muffs. I cranked the motor made sure it ran alright, the pump was pumping. Today I went out to double check my repairs and be sure its ready to go. I ran the motor for 5 to 10mins and the pee hole never peed. I got below...
  8. R

    9.8 running on one cylinder

    Some of you may have read some of my past posts about taking three old 9.8s and making one good one. Where I am at now is, the engine is running on the upper cyl only. I checked the compression, both cyls hit around 95psi one one pull. If you pull it again, it will hit 120. I am not sure of the...
  9. R

    Stop Button

    I just got finished taking three OLD late 60's, early 70's 9.8 motors and making one "running" motor. I am using a powerhead that has the ignition under the flywheel, no coils. I hooked up the water and it started right up. The stop switch on all the motors were in bad shape. There is a three...
  10. R

    9.8 powerhead swap

    I just bought three 9.8 motors two late 60's and one 70 model. One of the late 60's motors runs great but everything else is shot. One is incomplete,may some good parts. And one is really nice but it has the thunderbolt ign and it looks burnt up. What I want to do is take the good running...
  11. R

    7.5 sea king wont run with hood on

    I picked up a ROUGH Sea King 7.5 at a yard sale for next to nothing. I got her in a barrell and went to pulling. after my right arm nearly fell off I noticed a groung wire from the powerhead to the midsection had been cut and twisted back together. So I untwisted it and took it apart. On the...
  12. R

    19?? 9.8 ??

    Can any give me the year model please serial # 2798139. Thanks
  13. R

    2 stroke vs. 4 stroke

    I was looking at some new 15hp motors. The salesman said the 4 stroke was not as fast in an empty boat but just as fast or faster with a loaded down boat, 14' jon boat with 2 or 3 people in it. Any truth to that?
  14. R

    2 stroke vs. 4 stroke

    I was looking at some new 15hp motors. The salesman said the 4 stroke was not as fast in an empty boat but just as fast or faster with a loaded down boat, 14' jon boat with 2 or 3 people in it. Any truth to that?
  15. R

    ID my 15 Evinrude

    I am trying to find a lower unit for my 15hp Evinrude. I would like to id the one I have. It suppose to be a 96. Model #E15REDG seiral #604138166 If you know what models will fit that would be great. Thanks, Chris
  16. R

    Evinrude15 lower units swap (help)

    I have a 96 model Evinrude 15 short shaft. I need to know what year model range I could use a used unit from. They all look basicly the same for a wide span of year models.<br />Thanks, Chris
Top