Recent content by 1960 Starflite

  1. 1960 Starflite

    Need different prop for pulling

    We skied behind a 14ft Glastron with 35hp Mercury, early 70's.
  2. 1960 Starflite

    Need different prop for pulling

    Might want to consider a 15p or 17p four blade prop. It improves hole shot and earlier plane.
  3. 1960 Starflite

    MC-1 Drive Dog failure?

    My 1979 drive has spacers between the opposing tapered bearings. Preload is set by shimming O.D. and I.D. spacers then torquing nut. I don't know when the change went to "Rolling" torque.
  4. 1960 Starflite

    Resurfacing marine plywood decking

    CDX C=grade of finish one side, D=grade of finish other side (A being best in A - D) X meaning Exterior glue. It is Not Marine grade or treated. This was our 2nd time re-decking this Toon, first deck lasted 18 years with same grade plywood. Our Toon lived in covered dock, in water, six months of...
  5. 1960 Starflite

    Resurfacing marine plywood decking

    We redecked our 24 ft Harris. Carpet was badly faded, worn and mildewed. We went back with CDX exterior plywood and glued Vinyl flooring with 1" risers between vinyl and railings. Also installed 3/8" risers between furniture and deck. We are loving the easy cleanup with garden hose. Everything...
  6. 1960 Starflite

    3L cobra idling too high

    You may want to check the timing advance also. Advanced timing will increase idle RPM
  7. 1960 Starflite

    70’s Mercury 850 Thunderbolt - Distributor Wires

    Rotor IS PART OF THE SHAFT. Do not attempt to remove it. Bearings are replaceable in that distributor. I may have the numbers if needed. CDI may have a test procedure 🤷
  8. 1960 Starflite

    70’s Mercury 850 Thunderbolt - Distributor Wires

    Post in thread '74 mercury 850' https://forums.iboats.com/threads/74-mercury-850.761292/post-5807290
  9. 1960 Starflite

    70’s Mercury 850 Thunderbolt - Distributor Wires

    There was a post several years ago about exactly the same problem. He carefully ground out the filler material (Dremel maybe) down to contacts and was able to solder new wires on . I don't remember what he used as a replacement filler. Mercurys of that era had terrible insulation on wiring...
  10. 1960 Starflite

    Check your Prop Folks!!

    Good Catch !
  11. 1960 Starflite

    MC1 anodes

    3 blade aluminum on pontoon and 4 blade on Mercruiser. Boats sit in water May to October, no electric at mine or surrounding docks. Our lake is run-off feed. I considered it a 7 mile long pond.
  12. 1960 Starflite

    MC1 anodes

    Aluminum anodes didn't work at all for me in our sorta fresh water lake. Magnesium works very well. No more pitting on lower unit.
  13. 1960 Starflite

    Outdrive will not go back into transom

    Sure be nice if my driveway wasn't #57 gravel 😔
  14. 1960 Starflite

    Anodes for Yamaha outboard...Zinc or Aluminum?

    I'm in fresh water. My lower units on IO and OB had really bad pitting/deterioration . The aluminum anodes showed No deterioration. I switched to magnesium anodes, now I have no deterioration on outdrives.
  15. 1960 Starflite

    Going straight at low speed?

    My Century 190 is bad with wandering. 4 blade prop with trim down (if possible) helps but still there. Agree with small movements of wheel.
See more
Top