Sorry, premature posting. The kit is fine, never-mind the post. This is normal. The 3rd photo shows some extra rubber that was not pulled out and it was just left over from the manufacturing process. It peeled right out.
JOB DONE.
I am rebuilding my trim cylinders and the Wipe Seals seem too small. 1st time doing this service and I can't help but feel they should fit snug around the outer diameter of the cylinder.
I know the inner metal ring expands, but it is also very tight around the cylinder shaft. I did not want to...
Yeah it was like AHHHH I am frustrated.... I was not yelling at anyone. I understand all caps in communication and writing. But hey who cares about my boat anymore anyway.
I think we should just keep talking about all the mistakes I made in my post and how I should drill holes in my transom...
Ok, I used caps to stand out. The forum does not like it well just be plain and say something..... Two of you have hinted at it. I failed to read the, "read before you post"
Gather up the pitch forks yall! Does anyone want to help or did my, "YELLING" really upset someone. Consider title...
Hah. I read the same thing about no wood construction, but I did not know if that included the transom.
It is raining here but my moisture readings were about 5% all the way around the stern drive. Everywhere else was around 3.5-4% except behind the gas tank and it would show 6-7.5%.
If it is a...
Thanks for the info.
Currently I am waiting on all the shop manuals in the mail (i prefer the books).
The rust looks like it is from the manifold end cap seal front and back seals, also below the water pump, and thermostat. I am guessing there are tiny leaks there and they caused the rust.. I...
I did ask a question, what should I start with. There are tons of maintenance items, some important inspections, ........ Not what do I do now, but what order would make the most sense. I assume people here can see in the pictures that some items need addressed. I guess I could have made a...
Are you being serious? I used all caps on PLEASE HELP :) Is that a thing here that I should not be doing? Forum etiquette or something?
I hope no one else took offense to that, I was joking even with a smile...
Ok I will be posting a new thread this got out of hand.. Title will say, "Transom...
Ok so I see a trend here. Let me change the subject then. Who would replace the transom on this boat? And I do not mean what is the right thing to do. Who would actually spend the time or money on this boat to get that done.
Also I will probably take off the rear seat area and then start...
Hi Nola Mike, do you know of any info from the restorations area I can use to inspect the transom? I looked all the way back to the beginning of 2018 and saw nothing but repair threads with obvious damage.
As for drilling holes, every post and video I have seen only does that when their is a...
Okay. I am sure that it can handle much greater force than me, but where should I safely stand/bounce on this thing without breaking something or myself?
I am new to boating but I feel like I am being hazed lol! You got a new boat, drill holes in it and jump up and down on the outdrive lol...
I have not found any reason to believe the transom is bad. I am reluctant to drill holes. Is there another way to get an idea before that? This is an I/O. I have seen a moisture meter that is not invasive.
Well I just beat on the back all around the out drive and the left and right side sound the same. Tone changes the further you go from drive or side/bottom wall, but it is the same on port and star side. So maybe if there is a good way to inspect it from the interior I can quickly rule this in...
It has had 3 owners and 2nd owner put it up in a barn for some time after driving it often on the ocean ( think it was a manifold and water pump leaking that caused it, maybe). 3rd owner had it outside with a shabby cover for 2 years. I have no history or maintenance.
I just watched a video on...
Hi,
I just bought my first boat and it performs great, but it has a lot of rust. Took on a small amount of water on a two hour trip.
I will post some pictures. I am looking at a lot of work and service/maintenance. I have no idea where I should start from cleaning to rust to repairs... PLEASE...
