Recent content by blued

  1. B

    Anti Seize or Not?

    I've got the V6 and 25 lb-ft is what the manual states but that would need to be reduced if you use anti-seize. https://www.rocol.com/knowledge-centre/rocol_expert/a-deeper-understanding-of-anti-seize
  2. B

    Anti Seize or Not?

    Just remember if using any kind of lubricant/anti seize you'll need to recalculate the torque settings. I ended up opting for no lubricant on my manifold and elbow bolts!
  3. B

    Alpha One Gen 2 Whine/Whirring until 1200rpm

    Hi all, My sterndrive was recently written off due to hitting a submerged object. I bought a used lower unit from a local marine shop and they stripped, inspected, replaced top bearing, shimmed, and resealed my upper unit. New impeller kit and fresh oil. I now have a whirring/whining sound that...
  4. B

    Manifold and riser/elbow question for V6 Tahoe Q4

    Thanks Chris, I just meant that the 2008 Tahoe Q4 (as per original post) with this engine uses this setup. I appreciate there will be different configurations for older/newer boats and if my boat was a custom once off type thing or didn't have the original engine then I would have gone with the...
  5. B

    Manifold and riser/elbow question for V6 Tahoe Q4

    Just in case anyone stumbles across this thread looking for an answer, this model Tahoe Q4 uses the 14 degree elbows with no spacers.
  6. B

    Manifold and riser/elbow question for V6 Tahoe Q4

    The problem with that is it means taking the boat to the water and back again. I was hoping someone with a Tahoe Q4 could let me know what is on theirs.
  7. B

    Manifold and riser/elbow question for V6 Tahoe Q4

    That doesn't tell me if there are spacers required though? I've had two dealers come back to me to say the serial number doesn't provide that information. Edit: I did try this on the Mercury online one, it just lists all the spacers available.
  8. B

    Manifold and riser/elbow question for V6 Tahoe Q4

    Hi, Can anyone with a Tahoe Q4 that has the Mercruiser V6 let me know if there are spacers between the exhaust manifold and elbows? If so what size are they? My boat currently has aftermarket SS manifolds and I'm looking to replace with OEM. It's a 19'6 Tahoe Q4 built in 2008.
  9. B

    Advice needed on sterndrive replacement

    I should have said I'm in Australia in case you were thinking those were USD prices. I've seen a couple of cheaper shafts on eBay, about $350-400 each. There's also a cheap used set that have some corrosion - https://www.ebay.com.au/itm/223790509819 What's your thoughts on replacing...
  10. B

    Advice needed on sterndrive replacement

    The prop was aluminium surprisingly. It lost a complete blade and dinged a couple of the others but I thought it would have protected the shafts. The splines on both are twisted and the bend on the prop shaft made for a severe wobble. I should have said I'm in Australia, our market for spares...
  11. B

    Advice needed on sterndrive replacement

    Thanks for the info, reassuring that you've had 6 years out of one. I'll be impressed if the warranty covers hitting submerged objects!
  12. B

    Advice needed on sterndrive replacement

    Assuming you have one can you share a bit more info please? - How long have you had the drive fitted? - Do you use it in fresh/salt water? - Is your boat trailered or on a mooring/pen? - Any problems even if minor? - Is the finish/paint still in good condition?
  13. B

    Advice needed on sterndrive replacement

    I considered this but with enough impact to bend both shafts I expect bearings are likely to be damaged also? I spoke to a stern drive repair shop and they were saying approx $700 per shaft, $200 for seals, 4 hours labour per unit. They can definitely rebuild but said depending on internal...
  14. B

    Advice needed on sterndrive replacement

    It's a 3 year manufacturers warranty, although I've not looked into what it covers. I'd be interested to hear from anyone that has had issues covered under warranty and the turnaround times, our boat has been off the water for almost 2 months already which isn't something I want to repeat!!
  15. B

    Advice needed on sterndrive replacement

    Hi all, A friend ran my boat into shallow water when I was wakeboarding and damaged the sterndrive, an Alpha One Gen 2. The boat went in for assessment and the workshop found the propeller and driveshafts bent and twisted. They recommended replacing the sterndrive and coupling and provided an...
See more
Top