Hi everyone! I am redoing my transom currently and have my drive and shield off for the job. I have known for a while that the shield had a small hole drilled (maybe 1/4”-3/8”)for one of the exhaust relief. Not done by me! Is there any reason I can’t do a proper job and drill the hole properly...
I just want to make sure the part numbers in the sticky at the top of the forum apply to a 280 drive... Just installed my new engine, replaced pds bearings and seals, thought i'd go ahead and replace ujoints before installing transmission.
Thanks
Are the part numbers correct for a 280?
SPICER#...
Hi guys,
i ran into an issue the last weekend out. Long story short, i lost power and noticed a coupled hundred RPM increase on the tach at the same time. I recently had my prop rebuilt and rehubbed, I'm wondering if the hub can slip "partially"?
I WAS able to get the boat on plane but it...
Hello guys,
I was out at the lake this weekend and when I parked in a slip at the restaurant, I noticed a small oil slick coming from the back of the boat. We had dinner and then cruised back to the marina. When I pulled the boat out, the drain plug screw was finger tight. (Dunno how it didn't...
I spun my prop last night and am looking for a replacement. The only marking I can find on the prop are "C850864". I can't seem to find a cross reference or any matching props.
Any help?
Hello,
Just home from the lake and had a suprise when I pulled the boat up the ramp....
When attaching the rear tie downs I noticed the ring anode behind the prop is broken almost exactly in half. One half still attached, the other at the bottom of the lake somewhere. There is a little ding in...
HI guys! I'm in the process of building a custom seating area for my boat. I was hoping for tips on glassin' it to help with water intrusion. The original seat was rotted completely. The original wood was NOT treated in any fashion.
I want to put at least a layer of csm over this thing. I"m at...
Hey guys,
My oil pressure guage drops to about 10-15 at very low rpm and then jumps up to 50 or so when throttle is increased. This has happened the entire time i've had the boat and have been working on tons of other things. Now its time to address this issue. I seem to have plenty of power...
2004 Ram 1500 quad cab, 5.7hemi, it had a four wire trailer harness factory installed and there is another wire that was terminated and tied up at the harness at the rear of the truck (i was assuming for a brake lead)
I'm installing a trailer brake control and have reached a bump in the road. I...
Hello to everyone! I have a restore/refurb thread going but thought I'd post this question here. I have a 2004 Dodge ram 1500 with four flat trailer harness connection. The left trailer turn signal and brake light quit working. I went through all of the trailer wiring and it is NOT the...
Re: 1985 Bayliner 2450 Ciera Sunbridge Restoration underway!
I don't have a shower in the head, I have a deck washdown if that counts! lol
Heres some pics of the head (full of junk but you get the idea)
As you can see, I have been using the head for storage but the admiral is tired of...
Re: 1985 Bayliner 2450 Ciera Sunbridge Restoration underway!
This is the "super spacious" area where the water line fittings are located. The supply tank doesn't leave much room and it had to be in place to attach everything together properly. I got a bit frustrated trying to reach in there but...
Re: 1985 Bayliner 2450 Ciera Sunbridge Restoration underway!
I got the new water pump installed today. Works great! A bit frustrating working in such a tight area, but I got er' done. I went ahead and replaced the switch for the pump located in the galley. I had switches laying around and the...
Re: 1985 Bayliner 2450 Ciera Sunbridge Restoration underway!
I got pics of the shortened stern railing....
Also, as I was buttoning up all the connections to the water pump and testing everything out, I discovered that the pump leaks from the housing. I don't know if these things are...
