Recent content by EZSteury

  1. E

    Need a little help with spark plugs

    For My 1984 evinrude 35hp. I went to westMarine and they sold Me NGK BR7HS 10 but I removed a set of spark plugs from the previous owner with a different part #. Are the ones i got the best spark plugs for this OB.
  2. E

    84 evinrude 35hp timing

    I went back to the boat with the timing gun and hook it to the top spark plug cylinder, then I removed both plugs and grounded the bottom wire. I marked the flywheel at 26 degrees and set the timing gun to advance at 26 degrees as well, cranked the engine and it was off by far too retarded, so I...
  3. E

    1984 evinrude 35hp ignition issue

    Well today I had a chance to finally take the boat out for a couple of hours, it started fine and (thanks to some very helpful members from this forum) the new propeller performed very nicely. I do however have a ignition problem, it will randomly cut out at low rpms, I put the spark tester at...
  4. E

    84 Evinrude 35hp ?

    Re: 84 Evinrude 35hp ? Well I pulled the prop out and looking at it seems fine to Me but I did not test it in the water after the previous episode, the front reads "Michigan Wheel 012056A 10X13" the inside counts 14 teeth. I took it to a local shop and the mech said that by the looks it is...
  5. E

    84 Evinrude 35hp ?

    Finally after much work and thanks to this forum knowledgeable members I got the motor back together and drove to the bay for a test. I'm glad the motor now starts and runs, of course, I found a few problems. 1- The engine will cut off randomly for a fraction of a second and then continue as if...
  6. E

    1984 Evinrude 35hp

    I finally got some time to work on the new to Me evinrude I had to rebuild shortly after I purchased it, today I pumped some fuel in it and after some cranking I got it to fire up. I checked the spark prior to this and seemed weak to Me, then I tried to time it in case I moved something during...
  7. E

    Kill switch

    I have a 1984 Evinrude 35hp E35ELCRR I'm rebuilding and while doing this I have tried to repair some of the damage inflicted on the electrical system of this outboard, I have added a start switch, a fuse on the positive side of the charging system and solder new wires wherever needed. One thing...
  8. E

    1984? Chrysler sea king parts

    I have a montgomery ward sea king by Chrysler 7.5hp model vwb52179e in great shape but I think it needs a water pump kit, I was searching for parts and I can't find them. I tried boatnet website and there isn't a section for Chrysler at all, how do I tell which one it is? Thanks.
  9. E

    1984 35 Hp. Evinrude lost 1000 RPM

    Re: 1984 35 Hp. Evinrude lost 1000 RPM Here is a picture of the one I made, I used the spark plug but should only use a wire from the spark socket. Btw did You get My pm?
  10. E

    Anaerobic sealant

    I waiting for some parts to show up here and I got everything cleaned and ready to assemble when they do for My 84 evinrude 35hp, I was told to use the anaerobic sealant when I put the crankcase together and the HG as well, I went to Advance auto, Autozone and TSC but no one has it is there...
  11. E

    1984 evinrude 35 still wont start

    Re: 1984 evinrude 35 still wont start I will do that, thank You. Here is a pic with a circle showing the parts I should have on My carb but I don't have any of them.
  12. E

    1984 evinrude 35 still wont start

    Re: 1984 evinrude 35 still wont start Here is a picture from that link with the parts I'm missing on My carburetor from the throttle link to the choke which I'm missing completely, anyone have this little parts or know where I can get them? Thanks.
  13. E

    1984 evinrude 35 still wont start

    Re: 1984 evinrude 35 still wont start Well got a few minutes after work and pulled the head apart, the piston itself looks ok to Me, the top ring is fine and the bottom ring is in pieces, everything else looks fine or in better words shows the same normal wear. Here are a few pics of the...
  14. E

    1984 evinrude 35 still wont start

    Re: 1984 evinrude 35 still wont start I got together with My Dad and starter the tear down process, I never took one of this apart so far so I made a few mistakes, broke a couple of bolts I will have to drill out but I got the power head off (can't split it yet) and got a look at the piston...
  15. E

    1984 evinrude 35 still wont start

    Re: 1984 evinrude 35 still wont start Mine is E35ELCRR, I made a little spark tester and set it at 7/16", it has plenty of spark. While I was there with the plugs out I thought I should turn the flywheel and see how much vacuum and pressure I can get through the spark plug hole, the top...
See more
Top