Went out yesterday and took a bit to get her started once started I made it about 30ft out of the slip when she stalled. I was able to get her started again and she quickly died again. After a long period of not starting I was able to get her going one last time and I had her at a fast idle for...
Hello,
I am replacing a carb body on my 94 E120TLERC and noticed that the new replacement (part # 0436950) was missing a large brass tube. If you are looking at the face of the carb body the air jets are off to the left and directly below the throat there is a big brass tube (I assume high speed...
Hello, I am replacing a carb body on my 94 E120TLERC and noticed that the new replacement (part # 0436950) was missing a large brass tube. If you are looking at the face of the carb body the air jets are off to the left and directly below the throat there is a big brass tube (I assume high speed...
I just rebuilt 2 of the 4 carbs on my 1994 E120TLERC (other 2 on deck). I pulled the air mixture screws during the cleaning. I noticed one was about 2 & 1/2 turns of seat and the other was maybe a 1/4 of a turn off.
Is there a good starting point to back them off? or should I return to what...
I have a 94 Evinrude E120TLERC. We were out on the lake today for about 4hrs. She ran great until we went to run home. We idled out of the cove we were in and then cranked her up to about 80-90% of WOT. After about maybe 3-5min a continuous alarm sounded. My brother was driving so I told him to...
So I noticed I had some water in the lower unit/gearcase of my Evinrude E120TLERC so I drained it and added a small amount of pressure. Then checking with soapy water I noticed no leaks except for when the driveshaft was manipulated side to side air would shoot out. Purchased a new drive shaft...
Post drive shaft seal replacement I hooked her up to the hose to test for oil in the gearcase. Good news! No oil in gear case &steady tell tale/pisser Bad news water coming out of 4screw cover on the midsection of the engine. Why would water come from here? Pics attached
Ok so I am experiencing some trouble getting my 94 Evinrude e120tlerc started and it seems to be weak out of the hole. She has not sat more than 1.5months this winter. The last 2 times I had her out I had to squirt some gas into the carbs to get her to start. Once going she runs fine...no...
Dropped the lower unit to replace a water pump and noticed a lot of carbon or oil deposits in the exhaust housing. Do I need to do anything about this? Should I just scrape some of it out? I am afraid that cleaning might cause something to get clogged elsewhere. What about the upper portions...
Hello I am doing my first water pump replacement on my 94 evinrude 120hp etlerc. I am using an evinrude replacement parts and I noticed that the impeller plate is missing s deep grove/stamp in the side closes to the shift rod. Is this ok? Is it a change in design or did I get an incorrect part...
To avoid rewiring my entire boat or extending multiple 12V wires I am planning to adding pos & neg bus bars. All of the 12V wires end in the starboard compartment and I need to move my single 12V battery to the port compartment. I plan to use one of the bus bars listed below in the starboard...
Hello,
New to the forum and boat ownership. Although I have been around boats my whole life this is my first large outboard boat.
I recently purchased and '94 Evinrude 120. I took it to a local authorized mechanic to an inspection prior to taking my family out. I am mechanically inclined, but...
Ok so I bought a used B&S 5hp outboard a few months ago and it had minimal use. I went ahead and replace fuel lines, filter, and changed the oil. I took it out and ran it for 2-3hrs. It ran great, started every time no problems. Seeing as how it is winter her I have been going out once a...
