Recent content by johnmark

  1. johnmark

    1984 70 hp evinrude voltage regulator ?

    1984 70 hp evinrude , Does this motor have a voltage regulator ? Is it bad to disconnect the battery while its running. Thanks John Mark
  2. johnmark

    1982 70hp evinrude low speed adjustment ?All the way in then what ?

    I have a 1982 70hp evinrude cleaned carb.s need to know the low speed needle adjustment. thanks,John Mark
  3. johnmark

    Info. what Year/hp is this mariner "UPDATE"

    I have a mariner with serial number 6535832 can't find the model number or hp anywhere.would like to know the year & model, also if parts are still around. thanks a ton you guys.,John Mark
  4. johnmark

    evinrude 15012-46674 ? UPDATE

    :DWas wanting to know what year this motor is. And I have a old johnson service manual 10th edition is there a johnson motor the same year and make as this evinrude(15012) or one thats close to do my link & sink ? Thank you, Guys so much , John Mark
  5. johnmark

    lower unit removal 1961 5.5 hp

    I want to replace the waterpump on my 1961 5.5 hp evinrude (model 5522). Do I have to remove the powerhead? any tips/Hints ? also what would be the matching model # for a 5.5 hp johnson of the same year? Thanks Guys, John Mark
  6. johnmark

    Smoking 110hp

    I had a 1986 Johnson 110hp (J110TLCDC) No VRO , premix oil/gas 50-1 Smokes like a train pours white smoke and pure black goo seeping from lower unit. replaced all fuel lines no leaks did a decarb per Iboats forums. Let run on the muffs long time to see if it would stop after getting up to temp...
  7. johnmark

    # 1 cylinder On a V-4 / Timing

    I have a 1986 Johnson 110 hp (J110TLCDC) Need to know where the # 1 cylinder is located to set my WOT Timing and how many decrees @ what rpms. Going to back boat down the ramp to set my WOT Timing. Any tips would be nice ,Thanks a million GUYs..,John Mark :)
  8. johnmark

    WOT timing 110hp Johnson

    I have a 1986 Johnson 110 hp (J110TLCDC) I need to know what to set the wot timing ,Also if I use Joe Reeves method does this outboard have the fast start feature ? Thanks a ton guys. If you guys have noticed from my posts I started out with a 8 hp and have now went though a 35, 40, 48spl, 50 hp...
  9. johnmark

    Lead Shot

    What does the lead shot do in the carb? and how hard are they to replace? Should they be replaced each time you clean the carbs? Thanks, John The only dumb Question is the one not asked.
  10. johnmark

    interchange powerheads

    will the powerhead of a 1996 johnson 48 hp (J48BESLED) work on a 1983 johnson 50 hp (J50BELCTA)? I noticed the PWHD-ADAPT GASKET are the same . Thanks John
  11. johnmark

    What motor is this ?

    Just was given (free) a [J48BESLEDS] What year ? and she's missing the lower unit.would this be a long shaft ? Thanks you guys, John
  12. johnmark

    power pack coil wires (Top Plug)

    I have an 1983 johnson 50 hp (J50BELCTA) I just installed a new power pack and new coils trying to find out which wire goes to the top spark plug. And what would be the result if they were crossed? Thanks, John
  13. johnmark

    WOT rpm's

    I have an 1983 johnson 50 hp (J50BELCTA) what should the WOT rpm's be? I'm running a 12.25 x 15 SS prop and only getting 4200 rpms @ WOT and 22 mph on speedo. Thanks you guys., John Mark
  14. johnmark

    Idle adjustment after setting WOT timing?

    Thank You I have set the timing as Mr. Reeves said. model (J50BELCTA) . Started her up just fine on muffs ,out of gear. Was wondering what RPMs should I set the idle on muffs, out of gear? Before I had the idle set at 750 RPMs on muffs, out of gear.And when in the bay she wanted to and would...
  15. johnmark

    How to tell if you have Fast Start feature ?WOT Timing

    I have a 1983 johnson 50 hp (J50BELCTA). Was wondering if my motor has this feature(Fast Start). Am thinking of using Joe Reeves WOT timing setting on this Motor. Thanks Guys, John
See more
Top