Hello. . ..
Seems the seal went late last fall (I fish late into the year) and the lower unit side popped over the winter = ARRRGH
1992 E90TLend Long Shaft
My kids and Nephew are hounding me to go Musky Fishing . . . . .
Was hoping to find out what years / HP - evinrude's / Johnson's will...
Hello. . .. All
I have a 70hp evinrude with an outboard jet on it, and I wanted to make some fins for the intake foot, but am unable to find any good pictures or info on them.
I did see some fins (poor picture) that go straight down off the sides of the intake foot, and another set that angled...
Hello. . .. All
I have a 70hp evinrude with an outboard jet on it, and I wanted to make some fins for the intake foot, but am unable to find any good pictures or info.
I did see some go straight down off the sides of the intake foot, and another set that angled out from the intake foot...
Hey . . . Guys
I went and grabbed the serial numbers off the two motors that came with the cat I recently bought, and I did search the net and links offered here, but i could not figure out what year they are and model for the small one
Smaller one is: model ??
Searial: A1419814
The bigger...
Hello. . . . All
I have been searching for YEARS trying to identify my baby, and today I finally nailed her down.
Thanks to diligent hours of searching I have, beyond the shadow of a doubt, concluded she is a Duratech Comanche.
I was almost convinced by a local retired crestliner employee...
Hello. . .
unfortunately The motor ate a cylinder, and I need to sell this lower unit to be able to get a new motor . . . . PLEASE HELP
I was curious if one of you guys could tell me what other years of evininrude or Johnson motors this lower unit will fit.
as I said in the title, it is a...
Hello. . . .
I recently purchased a 1975 Evinrude 70hp outboard with a "Outboard Jet" on it.
Model - L
Serial - 7227
24" drive Shaft (overall)
I am planning on setting it up on an aluminum boat to run in the Spokane River here, and while I am a very competent individual and able to do a...
Hello . . . . I was wondering if there is a tach wire (what color) in the original OMC remote control, and if not what color is it at the engine terminal, and if someone could send me a link to a wiring diagram it would greatly appreciated.
Also will this work with a vintage 2 wire tach in a...
Hello. . .. .
I bought this boat / motor a year ago and it came with a new impeller in the boat, and I was curious if it is the right one for this motor. This one Measures 88 1/2mm across the fins, and the Shaft hole I.D. is 20mm, and it is 32mm thick.
I tried to call a couple local shops to...
Hello. . . . .
Can someone tell me the weight of this motor ??
I have a friend that is considering installing it on a 14' Fiberform, and I cannot find the weight specs online. . . .
Thanks in advance for any help
Have a Greta Week
Hello. . . . I have a 1988 force 1258F8B, and I need two float needles. I do not need a complete kit, so I am looking for the needles only.
The Merc # is FK10107
Let me know if you can help
Thanks for your time
Dave
Hello. . . .
I have a 1974 Evinrude 115, Model 115493-B Serial J0005126, and need to change the impeller out, but I I am not sure how / where to release the shift linkage to do the repair.
I know it is a simple as removing the lower unit bolts, and releaseing the shift linkage, but not sure...
Where the throttle linkage advances the timing there is an adjustment just under the flywheel which is a threaded plastic block with a piece of allthread & lock nut that advances the timeing as you throttle up (right?). I saw that the plastic piece the adjuster goes through had a crack in it, so...
Hello. . . I have a 1988 Force 125hp that was running fine, and now It only runs up to about 3900 rpm ( not full power) and I am using a gallon of gas a mile.
ANy suggestions as to what this might be ?? Floats ??
Also could someone tell me the factory suggested plugs for this motor, as My...
Hello. . . .
I have a 1992 Evinrude V4 90hp
WOT tops out at 5000, and I am doing aprox 32 MPH
The boat is an 18' 1/2 cuddy All Aluminum boat
The prop I just dinged is a
391198
13 3/4 X 15
I was curious if this looks liek the right prop, or shoudl I buy a different one when I replace the one...
