Search results

  1. MuskyHunterDave

    1992 E90TLend Long Shaft 90Hp V4 - - What other years / HP lower units interchage ??

    Hello. . .. Seems the seal went late last fall (I fish late into the year) and the lower unit side popped over the winter = ARRRGH 1992 E90TLend Long Shaft My kids and Nephew are hounding me to go Musky Fishing . . . . . Was hoping to find out what years / HP - evinrude's / Johnson's will...
  2. MuskyHunterDave

    OUTBOARD JET Intake FINS . . . Need some info

    Hello. . .. All I have a 70hp evinrude with an outboard jet on it, and I wanted to make some fins for the intake foot, but am unable to find any good pictures or info on them. I did see some fins (poor picture) that go straight down off the sides of the intake foot, and another set that angled...
  3. MuskyHunterDave

    OUTBOARD JET Intake FINS . . . Need some info

    Hello. . .. All I have a 70hp evinrude with an outboard jet on it, and I wanted to make some fins for the intake foot, but am unable to find any good pictures or info. I did see some go straight down off the sides of the intake foot, and another set that angled out from the intake foot...
  4. MuskyHunterDave

    I feel like an idiot, but I cannot figure out the year of these motors ?

    Hey . . . Guys I went and grabbed the serial numbers off the two motors that came with the cat I recently bought, and I did search the net and links offered here, but i could not figure out what year they are and model for the small one Smaller one is: model ?? Searial: A1419814 The bigger...
  5. MuskyHunterDave

    THE SEARCH IS OVER !!!! She is a Duratech Comanche

    Hello. . . . All I have been searching for YEARS trying to identify my baby, and today I finally nailed her down. Thanks to diligent hours of searching I have, beyond the shadow of a doubt, concluded she is a Duratech Comanche. I was almost convinced by a local retired crestliner employee...
  6. MuskyHunterDave

    1982 EvinRude 90HP E90MLCNB - Lower unit information needed

    Hello. . . unfortunately The motor ate a cylinder, and I need to sell this lower unit to be able to get a new motor . . . . PLEASE HELP I was curious if one of you guys could tell me what other years of evininrude or Johnson motors this lower unit will fit. as I said in the title, it is a...
  7. MuskyHunterDave

    Outboard Jet unit on 75hp Looking for information

    Hello. . . . I recently purchased a 1975 Evinrude 70hp outboard with a "Outboard Jet" on it. Model - L Serial - 7227 24" drive Shaft (overall) I am planning on setting it up on an aluminum boat to run in the Spokane River here, and while I am a very competent individual and able to do a...
  8. MuskyHunterDave

    1974 Evin 115 Tach Wireing Question + Diagram Needed

    Hello . . . . I was wondering if there is a tach wire (what color) in the original OMC remote control, and if not what color is it at the engine terminal, and if someone could send me a link to a wiring diagram it would greatly appreciated. Also will this work with a vintage 2 wire tach in a...
  9. MuskyHunterDave

    1967 80HP Johnson Impeller Issue V4SL-19R motor

    Hello. . .. . I bought this boat / motor a year ago and it came with a new impeller in the boat, and I was curious if it is the right one for this motor. This one Measures 88 1/2mm across the fins, and the Shaft hole I.D. is 20mm, and it is 32mm thick. I tried to call a couple local shops to...
  10. MuskyHunterDave

    1974 Evinrude 115 Hp 115493-8 Specs ??

    Hello. . . . . Can someone tell me the weight of this motor ?? I have a friend that is considering installing it on a 14' Fiberform, and I cannot find the weight specs online. . . . Thanks in advance for any help Have a Greta Week
  11. MuskyHunterDave

    I NEED FLOAT NEEDLES ONLY for my force 1258F8B

    Hello. . . . I have a 1988 force 1258F8B, and I need two float needles. I do not need a complete kit, so I am looking for the needles only. The Merc # is FK10107 Let me know if you can help Thanks for your time Dave
  12. MuskyHunterDave

    1974 Evinrude 115 Impeller replacment 115493-B

    Hello. . . . I have a 1974 Evinrude 115, Model 115493-B Serial J0005126, and need to change the impeller out, but I I am not sure how / where to release the shift linkage to do the repair. I know it is a simple as removing the lower unit bolts, and releaseing the shift linkage, but not sure...
  13. MuskyHunterDave

    Force 125 Hp 1258F8B Reinstalling Timing advance adjustmer

    Where the throttle linkage advances the timing there is an adjustment just under the flywheel which is a threaded plastic block with a piece of allthread & lock nut that advances the timeing as you throttle up (right?). I saw that the plastic piece the adjuster goes through had a crack in it, so...
  14. MuskyHunterDave

    Force 125 Hp 1258F8B Consuming gas + more

    Hello. . . I have a 1988 Force 125hp that was running fine, and now It only runs up to about 3900 rpm ( not full power) and I am using a gallon of gas a mile. ANy suggestions as to what this might be ?? Floats ?? Also could someone tell me the factory suggested plugs for this motor, as My...
  15. MuskyHunterDave

    Evinrude 90hp V4 Prop selection issue

    Hello. . . . I have a 1992 Evinrude V4 90hp WOT tops out at 5000, and I am doing aprox 32 MPH The boat is an 18' 1/2 cuddy All Aluminum boat The prop I just dinged is a 391198 13 3/4 X 15 I was curious if this looks liek the right prop, or shoudl I buy a different one when I replace the one...
  16. MuskyHunterDave

    Evinrude 90hp V4 Prop selection question

    Hello. . . . I have a 1992 Evinrude V4 90hp WOT tops out at 5000, and I am doing aprox 32 MPH The boat is an 18' 1/2 cuddy All Aluminum boat The prop I just dinged is a 391198 13 3/4 X 15 I was curious if this looks liek the right prop, or shoudl I buy a different one when I replace the one...
  17. MuskyHunterDave

    ??? Evinrude E90Tlend 90HP - Adaptor to PowerHead Gasket ???

    1992 Evinrude 90HP 90 Degree Model E90Tlend Serial G031533768 Hello. . . . I am planning on replacing the Adaptor to powerhead gasket (321727) on my motor this thursday, and was curious if you great guys with all your experience could give me any advice that the manual may not. Is there any...
  18. MuskyHunterDave

    1992 V4 90HP - which Oil injection tank kit do I need ??

    Hello. . . . I am looking to hook up the now disconnected VRO oil injection system on my 90, but am curious if they "OMC" tamks are all the same, or should I be looking for one type in particular. I looked on ebay, and found two: 1...
  19. MuskyHunterDave

    1992 Johnson v4 90HP Leaking Oil down Case ????

    Hello. . . . . I recently noticed a small amount of oil running down the outside of the case below the power head, and was wondering what this might be?? I pulled of the beauty plastic (below the power head), and one of the long exhaust bolts was loose, so I retighted them. . . . It only...
  20. MuskyHunterDave

    Is this the Right PROP ??? 92 evin 90HP 18' Boat 5200 WOT @35mph

    Hello. . . . .<br />Well I finally got the new motor on the water and was able to get the WOT rpms.<br /><br />I am curious if the prop it came with is the proper one, as I need to buy a second so I have a spare, and if I am able to change the pitch to attain more speed, or is this the best...
Top