Recent content by No more boats

  1. N

    Drive held pressure but still leaks out , water in

    Yes oil was milky but not as bad as when I dropped it before I changed seals Did soap spray , no bubbles top & bottom
  2. N

    Drive held pressure but still leaks out , water in

    What do you mean by not doing me any favors ? Thermal Expansion Never indicated, it was 20 or so minutes over two days, Just a moment ago I pumped 12 PSI into vent whole Holding , Understand most water intrusion is the prop shaft , I changed all 3 oil seals & screws with washers, If any of...
  3. N

    Drive held pressure but still leaks out , water in

    2000 OX 66 2 stroke 250 Hp SX 250 TXRY Had water in drive Purchased OEM Yamaha prop shaft seals , top seal , shift shaft seal Never considered doing a pressure test too determine which seal is bad , jut changed them all New screws and gaskets vent & drain Pumped 12 PSI , did soapy water test...
  4. N

    self leveling or motorized trim tabs

    22 ft grady white , seaferer 250 yamaha boat never had any trim tabs when i open up leans too starboard leaning towards self leveling , your thoughts self or motor leveling , what size plate ?
  5. N

    2 flat & wavy washers along with plastic washer not under impeller cover ?

    2000 OX 66 250 hp SX250TXRY shifting was ok prior too oil seals upyper & lower, plus shift selector seals , impeller , gear lube , OBs was new too me coming from IOs According to diagram 2 washers and 1 wavy washer along with plastic ring go under metal cover There was none on my shaft ...
  6. N

    Gears grinding after re- install drive

    2000 ox 66 2 stroke 250 hp pulled drive too change impeller top seals , bottom seals shift seal gear oil change ( water intrusion ) throttle in N did not move shifter while changing seal , shifter not easy too move without vice grips Installed drive gears grinding , forward slight grind...
  7. N

    oil injection fittings , tip broke

    thank you , ordered ,
  8. N

    oil injection fittings , tip broke

    FOLLOW up - REMOVED , WAS METAL , PRESSED INTO BLOCK , MADE A DIY HAMMER PULLER AND IT CAME OUT . NOW I HAVE TOO TRY TOO FIND THESE OLD PARTS
  9. N

    oil injection fittings , tip broke

    2000 TXRY yamaha OX 66 2 stroke ( obviously ) 250 hp oil injection hose on starboard side had crack leaking oil I should have known better but when I put a little force too remove and replace the tip of of fitting broke off into hose Of coarse location is very bottom bit tight but i can...
  10. N

    Starts then no start

    2000 ox 66 2 stroke 250 hp I had two issues same time , believe I corrected one , No spark starboard side all 3 cylinders , Found yellow wire into CDI crud and tips making no contact , New connection and now have spark OR A WEAK STATOR ( will explain ) Starting issue cold start ...
  11. N

    Water Separator , larger filter verses smaller filter

    Motor is a 2000 - 250 hp - 2 stroke - fuel injected SX -250 TXRY , Question regarding fuel - water separator 3232 Racor - presently installed on boat , larger filter with plastic base verses 3214 - smaller in size - clear base both 10 micron wanted too install 3214 - since there is a...
  12. N

    Yamaha ignition coils

    Proper testing equipment , TOOLS OF THE TRADE , do this for a living buy the best , Weekenders use once pay hundreds never using again , or can't find it if you need it , hire the guy , if you can find one , ( sometimes educated guess on part needed ) cheaper then hiring the guy ...
  13. N

    Yamaha ignition coils

    Boaters helping boaters . That's the beauty of this forum , Unless you ask questions one will never learn , OB new for me ( downsizing ) Having twin IOs learning as I go Correcting no spark on 3 cylinders starboard side , I wanted too check coils . not eager too replace if not...
  14. N

    Low Pressure Pumps - Yamaha

    2000 OX 66 250 hp 2 stroke fuel injected fuel priming issue , Difficult cold starting , once started , can shut and start over & over sit 1/2 hr , difficult starting again , Ball gets hard then soft What I did find out , one of 3 low pressure pumps leaks from back , TESTING LOW...
  15. N

    Yamaha ignition coils

    FOLLOW UP - FOUND IT - engine running on 3 cylinders . My first thoughts was water , but entire bank starboard had no spark, Checked every harness connection , opened every ground , wire brushed, dielectic grease, stator ? magnetic pick up ? thought I had computer but find out its...
See more
Top