Recent content by scr350

  1. S

    underwater lights

    i'm getting ready to install some under water transom lights, my boat has bottom paint on it........ will the 5200 still adhere to the bottom paint or will i have to sand the bottom paint off under the lights ?
  2. S

    alpha 1 gen 2 upper unit

    Re: alpha 1 gen 2 upper unit this is the seal kit i got off ebay from dgmarine,
  3. S

    alpha 1 gen 2 upper unit

    serial #od574021 i took the old drive shaft seal out of the case and my new kit came with 2 of the same seals, seloc manual shows 2 seals do both these seals go in? it had the spring facing downward, is this correct ? i also have a bigger seal that looks like it might go on the driven gear...
  4. S

    pics of plugged oil passge between lower and upper housings

    does anyone have a pic of how they block off the oil passage between the 2 housings? i want to pressure test my upper cause i have and oil leak out of the weep holes. i believe its the little seals at the bottom of the upper housing. while i have it apart i will pressure test the lower as well ...
  5. S

    sterndrive engineering

    Does anyone know anything about this company and its products. i am looking for a new alpha 1 gen 2 complete out drive and these seem to be really reasonable and carry a 3 year warranty
  6. S

    alpha 1 gen 2 outdrive

    took the boat out yesterday (1992 maxum scr2300) after i got back home i came out to find my outdrive leaking a few drops out of a hole on the port side (the hole was casted into the lower unit not broke by a part coming through it) right below the cavitation plate ! is this a seal that's...
  7. S

    prop diameter

    i was wondering if someone could tell me the diameter of this prop quicksilver 48 8278 A41 17P i know its a 17 pitch but cant find any info one it ! thanks in advance
  8. S

    Chevy est distributors

    i have a 1995 marine power 350 with the est distributor, it runs bad and smells of gas when idling. top in not good either and fouls the plugs. i have set the timing right and have the plug in wire to set it but it still runs really bad, i took a unilite distributor out of one of my other...
  9. S

    front accessories

    i was wondering if the alt,power steering, and everything on the front of the motor from a 2000 vortec 350 will fit on a 2000 vortec 454. it is a carb. setup both from mercruiser.
  10. S

    big block intake

    i need a part # for an aluminum intake for a big block gen 6 with the vortec heads. idle to 5500 should be fine.
  11. S

    going from small block to big block

    i'm wanting to change my vortec 350 to a 454 vortec. the boat is a maxum scr2300. i need more torque out of the hole. i have a 330 horse 350 in it now. my question is. can i keep my flywheel and bellhousing and coupler if i get the flywheel balanced with my new engine build up? thanks
  12. S

    timming issue..

    i have a 92 maxum scr with a reman. 350 vortec from marine power. i'm having problems timming it. its not t/b iv or a v. the distributor looks to be a gm unit. 2 wires comming from one side of the dist. to the coil and 1 wire from the other side of the dist. (white wire) going to the throttle...
  13. S

    ignition question

    i have a 92 maxum scr with a 350, it was repowered before i bought it with a carbed vortec motor, the distributor has 5 wires coming from it. 2 on one side of the module and 3 on the other. my question is which wire do i ground to set the timing. if i time it the way it now, its not even close...
  14. S

    transom assembly

    i need to replace the transom assembly on my 1978 searay with the 350ci. it looks like it has the pre alpha transon ***. but a alpha 1 ring. can i use a transom assembly from a 6cyl. or even a 4cyl. of the same type. alpha 1 gen 1
See more
Top