I have a trophy 1802 with a Merc Saltwater series 125 outboard uses a stator and not an alternator. It says that it produces 17 amps at WOT. Is this enough to charge two batteries? I have 2 now and I'm looking to replace them because they are 5 years old and they don't hold charge as well as...
I was thinking about putting a lewmar pro-sport 550 windlass on my boat. I have a dual battery setup already but my engine is a Mercury 125 and the charging system only puts out 18amps. In the product specs it says 150w ( 150w\12v= 12.5a). But then it says Current draw at working load: 35a...
I have a mercury 125hp outboard motor on a 1802 Trophy. The steering was tight last year and over the winter I took a look at it. I disconnected the motor from the steering assembly and worked it back and forth and it moved freely. I disconnected the cable and lubed the cable good with merc...
I have a Mercury 125hp outboard. Mod#1125422zy Ser#0T509164. I'm replacing the shaft seals (upper and lower seals)under the water pump. Part#'s 43035 and 43036. The seals go back to back in the water pump cover assembly. I thought with the 2 seals back to back that they would be...
When I changed my lower unit oil it came out a thick white fluid. No water came out. ( I heard some people say they got some water and then fluid ) Put in a glass jar and after 2 days there is still no separation. If water changed the color of the fluid wouldn't it separate from the fluid...
I have a merc 125hp year 2002 outboard. When I drained the lower unit it came out a thick white fluid. I assume I need to replace seals. I replaced my water pump before and have a shop manual. Would this job be better left to a pro or is it not that bad? Any idea what it would cost have the...
Can anyone recommend a mechanic in NE phila area. Changed lower gear oil and it was white. What kind of coin do you think I'm looking at. Merc 125 hp outboard year 2002. I assume the labor might be to the point that I should be shopping for a lower unit. I've changed my water pump and have a...
My flares say exp Nov 2010. Does that mean they are legal till the end of Oct and exp Nov1 or are they good till the end of Nov. I thought Nov 1 but my buddy said end of Nov.
Thanks for input,
Tom
new to saltwater and was going to use the flushing adapter that came with my Mercury 125 saltwater 2 stroke outboard. I have read that you don't want to put the hose on full pressure because it can cause damage to motor. Do I flush with motor up out of water or do it before I trim it up out of...
I installed a new transducer last year. Installed it within manuf. specs. Worked great up to about 25 feet. After 25 feet it showed a bunch of noise. Marking at all levels. The markings happened at moving and at anchor. Below 25 feet seemed to work great even when up on plane. The depth...
My boat is in a slip during the summer and I want to replace the bunks on my trailer. Should this be done right before pulling the boat. I'm afraid of finding nice straight wood only to find that it has warped from being in the weather. My thinking is to do it right before pulling the boat so...
I have a Mercury 125hp outboard. After having no problems out fishing I came in and shutoff the motor and heard a clunk. I thought maybe it was in gear but it wasn't. I started it up again to see if it would do it again and it did. Starts right up sounds normal but when I shut it off there...
Hope to have more info tomorrow but not sure what to look for. Came in tonight and had no problem with motor. After I docked the boat I shutoff the engine and heard a clunk. I've had the boat for a couple years so the noise is something new. Wasn't sure if I was hearing things so I started...
I need a Bendix drive for my starter on a Mercury 125 outboard. I like to stick with O.E.M. parts whenever possible. Is there a difference between getting a Mercury Bendix vs a Quicksilver? The dealer said they are the same part in a different package.
Thanks for your input,
Tom
I need to replace the starter drive on my Merc 125 outboard. It shows using part# 111 on the helix threads. The manual shows using sae10 on the threads. Is this the same thing. There is an index to all the different lubricants and thread lockers but 111 is not one of them. What do you guys...
