Recent content by tullydf

  1. tullydf

    Crusader starter not cranking

    I have a 1988 Crusader 350 (270HP) and when attempting to start the engine today, the starter did not crank. It was working fine this past weekend. While attempting to crank it over from the bridge, my wife noticed a burning smell and some light smoke. She did not know where it was coming...
  2. tullydf

    1976 Ted Williams 15HP

    Re: 1976 Ted Williams 15HP Well...it's done. I hope I did you proud. Here's he pic...
  3. tullydf

    1976 Ted Williams 15HP

    Re: 1976 Ted Williams 15HP Here is a pic of the spacer with bearing sleeve...
  4. tullydf

    Looking for trailer

    I have a 13 foot tiderunner that I need a trailer for. It is almost identical to a 13 boston whaler (same exact hull). I am located in Poughkeepsie NY and am looking for either brand new or good condition used. Anyone with suggestions please share. Thanks!
  5. tullydf

    Mariner W48

    I have a Mariner W48 outboard. I am wondering if anyone else out there does or if anyone knows of a good place for parts for these. I believe it is a mid to late seventies vintage. I got it running after it having sat for 25 years. Will need to replace impeller and hope to converse with...
  6. tullydf

    1976 Ted Williams 15HP

    Re: 1976 Ted Williams 15HP Mr. Crabs, I am attaching a few pics of the shaft, spacer, and bearing. The bearing came apart upon removal and the little balls went all over. I was then able to get the inner sleeve off the shaft. The inner sleeve to the bearing looks to be part of this long...
  7. tullydf

    1976 Ted Williams 15HP

    Re: 1976 Ted Williams 15HP Mr. Crabs, The bearing says Nachi 7201 Japan.
  8. tullydf

    Different Shaft Lengths on Inboard

    Last year I had a shaft replaced by a hauler whose trailer bent my previous shaft upon removal of boat from water. When the job was completed and I was prepping the shafts, rudders, and props for launch, I noticed that the new shaft was about 3/4" longer than the other side. I took the...
  9. tullydf

    Sherwood E-35 Raw Water Pump

    I have twin 350 Crusaders and am in need of a new Raw Water pump. I need the Sherwood E-35 but have noticed since I purchased my last one two years ago for about $320 the price has sky rocketed. Even the rebuild kits have soared through the roof in price. Anyone know why this is?
  10. tullydf

    1976 Ted Williams 15HP

    Re: 1976 Ted Williams 15HP Help Mr. Crabs...I cannot remove the shaft. I am attaching the pictures of what I am dealing with. How do I remove the plastic piece below where the water pump was?? Please help. Thanks! Dave
  11. tullydf

    Evinrude 115

    I have an evinrude 115 and do not know the year. Where is the serial # located? I found one on the transome bracket, but it is for a Johnson motor. It is a V4. I am attaching pictures that may aid in identifying. I did buy the motor from Outboard Exchange in Waterford CT, who specializes in...
  12. tullydf

    1976 Ted Williams 15HP

    Re: 1976 Ted Williams 15HP Mr. Crabs, The actual model number is 217-586310. I took some pictures with my iphone, they are below. I have worked with copper tubing so I am confident I could fabricate something if I must. There is a water tube on ebay, but it is from a 9.9 model #217-58621-0...
  13. tullydf

    1976 Ted Williams 15HP

    I have a 1976 Ted Williams 15HP s/n(217-587610) outboard that my Dad purchased new from Sears. It had sat for years and years in his garage, Since 1978. Last year I started to work on it. It started after a few pulls and I actually used it. It ran a little rough, but not too bad. This...
  14. tullydf

    Inboard shaft length

    I have a 36' Mainship Nantucket and recently had the starboard shaft replaced. The person who replaced the shaft did a great job and also replaced the cutlass bearings. Upon final inspection of the job, I realized that the new shaft was about 3/4" longer than the old shaft. Subsequently, the...
See more
Top