I have attached some pictures of our 1960 Mirrocraft 16ft tinny called "The Tin Man" I needed to be able to pull tubers, skiers and kneeboarders and also fish with some efficiency. Hard to work this out in a tin runnabout.
We opted for a wood floor running from under the front seats, flat all...
Can someone fill me in on how to time and sync my 1984 model 110 (9.8 hp)
I use it s a kicker and it used to push my boat along and 7 to 10 mph.
The plastic throttle lever on top of the carb broke, I got a new piece. I assume it needs to be put on and adjusted so that it allows the butterfly to...
I have a 1971 merc 800. I need help with making sure the timing marks are right. My flywheel has a single row of three dots and a white dot painted on the top above them.
When the #1 cyl is at TDC the timing marks on the flywheel should point at the #1 TDC mark on the cowl decal correct?
The...
I got an old 1970 merc 800 that I am trying to bring back to life.
I had split the case, replaced the top and bottom crank seals the cork seals on the case halves and used the correct locktite anerobic goop to seal it up. I took a real close look at the reeds,
all look ok none bent or broken...
I am working on awakening a 71 merc 800. It was hard to start, would rev to high RPM and then would not idle, and then die.
I tore it down to inspect reeds and case seals. Reeds look really good. Bottom crank seals not so great and O ring on bottom bearing cap was broken and cracked. So I will...
I am familiar with the various sealants reccomended to seal the two halves of my merc 650 crank cases. There are no gaskets on them. I have cracked open a merc 800 that I aquired and I see that it has two cork seals inset into the casting flange where the two halves come together. If I replace...
I picked up a 1971 merc 800. It had been sitting for a few years. It has excellent compression and a hot blue spark on all four cyl. I have it running but it will not idle.
When I bought it it would not fire at all. new plugs, took off carbs and they were a mess, full of gunk. I pulled them...
I just picked up an early 70's Merc 800. It is extremely similar to my two merc 650s. It looks like the bore is the same, I am not sure about the stroke.
Does anybody know how they get the extra 15 HP out of the 800 vs the 650? What are the differences between the two?
Also, does anyone know if...
I have a lat 60's merc 650 that runs very well. On the top of the block there is a plug that opens into the water jacket.
Can use this in anyway to add a water pressure idiot light or a gauge?
If so do I need to block the pee hole if I do this?
I have to walk back to the transom to see if water...
I am running a 1969 merc 650. I also have two more of these motors in reserve, but neither has a lower unit. I also see a lot of these on ebay and other places for sale but without a lower unit. I never see a lower unit for sale anywhere. I was considering a stainless prop for my motor, but if...
HI,
I wonder if I am in the best overall configuration possible.
Boat is elderly 16 ft by 6.5 ft beam aluminum semi v runabout with closed bow, plywood floor. I think that it is heavier than it appears to be.
Motor is 1969 merc 650 four cylinder (65 hp). Runs good, 130# compression.
First...
I have an old 650 merc with the lightning energizer ignition.
I used CC's post on how to do rough timimg.
Then we went to the water and actually put the timing light on it at speed.
Wide open I have 38 degrees total advace against the stop, that is what the sticker on the motor says it should...
I have a 16 ft semi V aluminum runabout with a 1969 650 merc.
Prop is mercury 3 blade 13 3/4 X 15 I can get 28 mph wot. 3 people 10 gal gas.
Tach is brand new but a bit goofy, It shows 4000 at wot but it sounds a bit higher then the tach will peg from time to time.
Do you think a bit less...
