Search results

  1. E

    OMC Evinrude reed plate part number?

    Can someone tell me the part number for just the reed? 100 hp E100WTLCRS 1984 v4. Not the reed assembly. Found it sorry 317739. I don't know how to delete a post.
  2. E

    Recirculation Tee Install

    I am open to suggestions for installing 1/16 BRP 326449 hose onto 5 way barbed fitting 329688 that I now have to replace. OPPS.:eek: I tried both windex and isopropyl alcohol as lube but I guess PB blast would have worked better. Has anyone seen these 5-way barbed tees from brass? I have see...
  3. E

    Throttle Play V4 84 100hp

    Guys, I have all the parts in throttle cleaned and lightly triple guard greased. See attached diagram item numbers 76 and 82. These seem loose side to side after installing the washer and lock nut. Is this last washer supposed to fit up over the shoulder? I would think this assembly would be...
  4. E

    Evinrude 309924 bolt length

    Can someone confirm for me the bolt length of 309924 bolt for lower crank bearing to crankcase not the one for the bearing plate? This is 1/4-20 x 7/8 hex with star washer I think?
  5. E

    Reed Gasket and Carson Reeds

    I have a question about the new reed gaskets having a sticky side but the old ones did not. Which side does the sticky side go. I guess reed cage side but would not like to guess. Just installed some Cris Carson reeds and after lapping the cages flat and installing the new reeds they are not...
  6. E

    V4 crank case btm half modifcation

    What grinding/porting if any can be done to the btm crankcase half ? I heard it was possible. I have found the intake manifold top middle cut stuff on here and that looks interesting to do.
  7. E

    Needle Valve keeper to float missing. Evinrude 100hp 1984

    What would the symptoms be on 1984 100hp evinrude if one of the needle valve keepers was not attached to the float and actually missing? Anything is possible but I think the keeper was not there when I took it apart. Thanks.
  8. E

    Crankcase Spagetti seals

    I was almost finshed with powerhead reasembly when I went to install the spagetti seal I noticed right from the zip lock bag one of the branches was missing. You can see a divot where the section was attached at one time. Question is would I be better off ordering another one, gluing a branch...
  9. E

    Cork thermostat gasket location E100WTLCRS 100hp 1984

    Guys, I have two OMC service manuals(one for 1984 and the other for 1988) and one shows the cork gasket inserted into the valve body first and the other one shows the thermostat inserted first and the cork gasket over the top. Can both be correct?
  10. E

    1984 fuel pump 100hp Are there two different sizes?

    Just received the superseeded fuel pump kit but the "correct" part is larger than original. The main casting has 322843 part number and one of the plastic parts has 321671. The received kit is part number 398514 but old part number for kit is 393867. IF the body of the pump is "house shaped"...
  11. E

    Evinrude fuel pump kit

    Hello everyone and thanks for all the help. I am curious if my fuel pump is not original. Is the number ink stamped on the side the assembly part number? That number is hard to read. E100WTLCRS is outboard. 100hp 1984 commercial duty. The main casting of the fuel pump has part number 322843...
  12. E

    bored and honed .044 over but looks very thin

    83 Evinrude 100hp. I have all new Wisco pistons have the block bored and honed .044 over but the steel sleeve looks very thin on one side especally at the "splines" at the ports. Does anyone know what wall thickness (at this thinest splined area) is acceptable? Does this "spline" go all the way...
  13. E

    Crankshaft Seal Rings Evinrude V4 1984 100hp

    OMC service manual describes replacing seal rings according to stripe code. Can someone please tell me what the stripe code means? My seal rings look worn on one side and would like more information about clearance or stripe code mentioned. OMC lists them for sale according to stripe code 1, 2...
  14. E

    v4 xflow evinrude crankshaft seal rings

    In process of first rebuild and would like to replace crankshaft seal rings as they look worn OMC service manual mentions to change them according to stripe code (1,2 or 3). What or where can I find information about stripe code? I have feeler gages to check clearances. FYI 1984 V4 crossflow 100...
View older results
Top