Search results

  1. Skidude17

    To fill or not to fill

    i pulled the engine on my 1969 Glasply with a Volvo AQ150, and the lag bolts holding the heat exchanger tower were rusted to the point of breaking. I've finally dug out the shaft of the bolts that were stuck in what I sssume go be the stringers, but now I'm left with these big holes. Do do I...
  2. Skidude17

    Stainless steel vs zinc plated bolts for kicker mount in salt water

    I'm about to install the kicker mount for my 1979's Honda BF100 (10hp) on my 19' Glasply. It has a thick transom (about 3") so I don't plan on beefing it up any more (the 500+ lb cast iron AQ150 has been hanging on it for almost 50 years without a problem). My my question is what kind of bolts...
  3. Skidude17

    Kicker fuel line to main gas tank setup

    I'm connecting my fuel line for my kicker to the fuel line for my AQ150. I'm taking Don S advice in this post https://forums.iboats.com/forum/engine-repair-and-maintenance/mercruiser-i-o-inboard-engines-outdrives/184466-tapping-into-the-existing-fuel-tank by adding another fuel line off the...
  4. Skidude17

    A270 where is the "right" place to position all the hose clamps

    I have a 1969 19' Glasply with an AQ150 and an AQ200 outdrive. I know the title says AQ270, but most people don't recognize the 200 as an outdrive, and for this instance everything should be the same. I'm trying to figure out the "right" way to orient all the hose clamps for everything between...
  5. Skidude17

    Aq270 Where are the tabs on the transom shield for alignment

    I pulled the engine on my AQ150 / 270 to replace the PDS bearing and seals. Now I have the engine back in, and don't see any tabs on the transom shield to align my engine. I imagine they would be at the 12, 3, and 9 o'clock positions, but I don't see anything there. I attached a pic that...
  6. Skidude17

    Help identify volvo outdrive on an AQ150B by model and SN. PZNR B223768 SN:2977923

    I need help identifying my outdrive so I can be sure I'm buying the right parts. The engine is a 1969 AQ150B (Buick V6). The numbers on the upper part of the outdrive are PZNR B223768 2977923 For those of you that don't think I have enough numbers, I have attached some pictures of the plate...
  7. Skidude17

    Products / how to refinish a Rusty engine

    I have a 1969 225 cc Buick Dauntless engine out of my 19' Glasply that is extremely rusty. Due to other issues, I had to pull the engine anyway, so I want to knock off the rust and refinish it. I've already removed all of the wiring and exhaust manifold/risers. I'm thinking about doing the...
  8. Skidude17

    AQ150B PDS bearing part number?

    After a bunch of research, I finally found the Volvo nomenclature for my engine. It's an AQ150B with a 270 drive. The engine is a Buick 225 V6 oddfire. There is only one other post on this entire forum that mentions the AQ150 that I can find, but it's backed up by a couple of European websites...
  9. Skidude17

    270 v6 buick engine with only one bearing on drive shaft?

    I have a buick v6 225 oddfire with a 270 drive. Everything I've read says there should be 2 bearings on this drive, but all evidence points to only one bearing. The first two photos are from the engine side of the flywheel housing. There doesn't appear to be a place for a bearing. The last...
  10. Skidude17

    Volvo 270 Stripped threads on clamp ring

    I am in the process of pulling my engine so I can change the PDS bearings for my Glasply with a Buick 225 V6. When I went to jack the clamp ring off, I ended up stripping the threads on the clamp ring. Now I have a stuck clamp ring. I removed 6 bolts from the flywheel housing, all the electrical...
  11. Skidude17

    270 u-joint bearings stuck!!!

    I've had this 1969 Glasply with a 225 V6 Buick engine and 270 outdrive for about three years, and every year I keep hitting a roadblock that keeps me off the water. I'm relatively new to boating, and I'm learning everything the hard way. After searching the forums, I've discovered I should have...
  12. Skidude17

    How to ID a 4cyl aq 270 outdrive versus a larger aq 270 outdrive

    I have a volvo penta 270 outdrive powered by a buick v6. I found a complete outdrive with the transom shield and tilt motor on craigslist for $175, but I need to make sure it is not the 4 cylinder version. Are there any easy ways to identify which version the 270 outdrive is? Thanks in advance...
  13. Skidude17

    Will an 11 spline starter work for a 9 spline application?

    I have a 1969 Glasply with a buick 225 3.7L V6. I'm having trouble finding a marine starter for this application. The ACDelco part number is 336-1860, but it's not a marine starter. I asked a marine starter dealer on amazon if he has the right starter and he sent me...
  14. Skidude17

    How to find marine starter part number?

    I have a 1969 buick 225 dauntless with a bad starter, but I can't find a marine starter for it. After doing some research, Universal marinised these engines during that time. The ACDelco part number for the starter is 336-1860. Is there an easy way to find the marine starter part number?
  15. Skidude17

    Grinding noise when turning 1969 Volvo Aquamatic outdrive

    I had my 1969 19' Glasply with a Buick 225 V6 engine and Volvo Aquamatic outdrive out shrimping this weekend, and started to hear a grinding noise coming from the outdrive halfway through the day. While motoring back to the ramp, I noticed it was worse when I turned, and I could almost get it...
  16. Skidude17

    1969 outdrive gear oil fill location

    I'm trying to change the fluids on my 1969 glasply with a 225 buick and a volvo outdrive. On the outdrive, I see the drain plug at the bottom, and the dipstick at the top, but I don't see any fill plug or a site plug to let me know when I've put enough in. Do I just fill through the dipstick...
  17. Skidude17

    Need a longer choke cable or an alternative

    I'm converting my automatic choke to a manual choke, but the conversion kit came with a cable that is only 5' long. I want a longer cable, so I can operate the choke from the helm. Does anybody know where to get a choke cable long enough, or how to convert some other kind of cable? I have a...
  18. Skidude17

    Rust in carburetor

    It turns out my starting problems probably aren't from the choke. I took the carburetor apart, and found rust in the float bowl and fuel intake. There is already a water fuel separator installed, and I don't see any other fuel filters in the line. I want to add in line fuel filters in front of...
  19. Skidude17

    1969 Buick V6 225 "Odd Fire" stove pipe connection location Rochester 2bbl carburetor

    Is the whole supposed to be in the intake manifold, or part of the exhaust? Also, do you know what the hole should look like i.e. just a hole, some kind of connector, a nipple...? I will try to get more pics posted tonight.
  20. Skidude17

    1969 Buick V6 225 "Odd Fire" stove pipe connection location Rochester 2bbl carburetor

    1969 Buick V6 225 "Odd Fire" stove pipe connection location Rochester 2bbl carburetor I have a 1969 Glasply with a '69 Buick 225 and a Volvo outdrive that I inherited. It runs well while cold, but is hard to start when hot. After running through all of the electrical, I started on the fuel...
Top