Search results

  1. 1

    Uniden Microphone Replacement - How

    I need to replace the microphone on my Unide (Polaris) VHF radio, I can't figure out how to remove the mic. connector. I removed the control head and looked inside and it looks like it's completely sealed. I know it unplugs from the inside, I just can't remove the cord from the radio. Ant help...
  2. 1

    6 HP Johnson - Removing Throttle Handle

    I need to replace the kill switch on my 1990 6 HP Evinrude motor, I have tesed the switch with an OHm meter and detemind it was faulty. I pushed in the 2 release buttons on the handle which made it loose, but I could'nt figure out how to get the rest of the handle off. I assume there's some...
  3. 1

    No Spark 6HP Evinrude

    I have a 6 HP Evinrude which I belive is a 1993 modle (E6RLESR) that's not getting spark on either cylinder, is it possible for two coils to fail @ the same time? How do I test a coil? I already pulled the plug and held it to ground while somebody pulled the rope, I also pulled the safety...
  4. 1

    Dirt Water When Flushing 4.3 Liter Engine

    I recently purchased a Invader boat with a 4.3 liter engine, the boat seems to run ok without any detectable issue. When I took the boat home I flushed the engine with ear muff for a few minutes and everything seemed ok. After sitting for a week I flushed it again and the water that came out...
  5. 1

    4.3 120 HP Thermostat Issue

    I have an 1986 4.3 liter engine I recently purchased, I alway like to know what the engine tempature is. The guy I bought the boat from said he just installed a new thermostad (Which does look new) a few weeks ealier, the problem is the boat need to run for almost 30 minutes befor it registers...
  6. 1

    Dual Axel Trailer Noise -Take off & Stops

    I have a dual axel trailer I recently purchase (with a boat) that has a brake system, when I first connected it to my tow vehicle I thought something was loose. When I take off I hear a delayed bang that sounded like my tailer hitch was loose, when I stop I hear the same thing. The guy I bought...
  7. 1

    GPS for Dummies

    I have a Garmin handheld GPS and want to figure out how to understand the Lat/Lon information. In my area the main readings are the 33 XX & 118 XX, I'm trying to figure out what the 33 or 118 represent. Are they miles, if so what is the XX and the XXX represent? Somebody told me all I need...
  8. 1

    Windless Gypsy Cluch Nut

    I hope this is the right forum for this topic, I have lost the nut that tighten the rotaing gear on my windless. The modle is a Lewmar/Horizon series 900, I called Lewmar and they said I can't get a replacement until the end of November. Does anybody know where I might find a replacement nut...
  9. 1

    120 Twin Force Engines

    Just purchased a pair of 1992 Force 120 HP motor, the guy stated that one works great and the other had a gasket leak. I plan on using only 1 of these motors for a ski boat, somebody ask me if one has a reverse prop on it. How would I tell and does it make a difference on which one I use...
  10. 1

    Furuno LS 6000 Problem

    Hi Guy's, My Furuno LS6000 Video Sounder stop scanner, it powers up just doesn't move the screen. Does anybody know of a reair shop in LA California area, I'm located in Torrance and can't find a local repair vendor. Thanks for any information that may help. Jerry (Lost at Sea)
  11. 1

    Furuno LS 6000 Fish Finder

    Having a problem with my Furuno fish finder and can't seem to fine a local service shop. The screen no longer seems to scan, but it powers up fine. If theres a differnt site that may help, please let me know. Jerry
  12. 1

    1984 Johnson 35 HP Top End Speed Problem

    I have a 1984 Johnosn 35 HP motor that runs great from idle to mid speeds, but when I run at higher speeds it feels like the prop is slipping. The motor sounds like the RPM rise but then I lose a little power. How can I determine if this is a prop issue or a lower unit issue? Thanks for any...
  13. 1

    1989 Starcraft Leaking Problem

    I have purchased a used 1989 18' Aluminum Starcraft fishing boat and have several leaks that have been repaired by the previous owner in two ways. 1. "Below Water Sealants" available @ most boat shops. 2. On soft spots he drilled screws into the hull and then used the sealant. My concerns are...
  14. 1

    No water out of exhuast at high speed 35 Johnson

    Hi Guys, I have a 1984 35 Johnson (J35ELCRR) with a new water pump, it test good on the hose and when going low speed on the water. The water also is coming out of the 2 exhaust holes until we pick up speed. The water will still come out of the pee hole, but not the exhaust hole and it seems...
  15. 1

    1971 Johnson 20 HP Water Relief Ports?

    I have a 1971 Model # 20R71S that I just purchased, it has set for a couple of year according to the previous owner. My question is should this motor have a water "Pee Hole" to verify the water is circulating? I have a generic manual that covers many differnt years. I don't see a water hose...
  16. 1

    Aluminum Boat Leaking

    Hi Guy's, I just bought an aluminum welded boat that seems to leak on the seems. I thought weld boats didn't leak... But now I have and need to fix it. Is it better to seal and paint the bottom half or actully try to have it welded. I plan on leaving in the water for about 3 months. if...
  17. 1

    Shimano Tek 600 Fishing Reel... Any good?

    I'm looking to purchase the Shimano Tek 600 sports fishing reel, is this a good reel? Looking for yellow-tail or dorado, maybe even some albacore. Thanks
  18. 1

    Adding cut-out tot he bunk boards

    I use the Redondo Beach Hoist to luanch my boat, if I have the cut-out on my bunk I get a discouted rate. 1. How can I lift my boat high enough off the trailer to safely exchange the bunk boards with new ones? 2. Is any 2X8 wood ok for building these new bunk boards, or is there a speacial...
  19. 1

    1984-1986 in-line Six Thermostad problem

    I'm trying to find a way to install an tempature alarm, when I checked with the dealer that said the 84-86 mercury only have a sensor without switching capabilities. Has anybody found a way to install a tempature alarm on the older modles? My current gague works fine, but I'm not alway...
  20. 1

    Trim up or down?

    When the motor is trailered should the motor be stored with the trim up or down? It seems like its under pressure in the down position? Thanks
Top