Search results

  1. G

    Non functioning temperature gauge..

    Nothing there on the intake..
  2. G

    SeaDoo Tow Tap

    2021 RXT-X300. Do I need to install a Tow Tap valve to prevent water from entering the engine while under tow ?
  3. G

    Non functioning temperature gauge..

    Thanks. I'll check it out...
  4. G

    Non functioning temperature gauge..

    2020 235LR, Merc 6.2 300hp, 2A636272 engine. Anyone know where the temp sender is on the engine ? Found a 2 wire temperature sensor but I think its for the ECU..Only one I can find on the diagram. Thanks..
  5. G

    Are surge brakes always a PIA?

    I have surge brakes on my 2013 tandem axle Eagle trailer. They don't run a ground wire for the reverse lock out solenoid. It grounds through the ball.. I noticed since I painted the top of the ball yellow to see it better on camera, I lost the ground.. So I have to run a wire. My previous...
  6. G

    Bomar Hatch Seal Repair

    2013 Stingray Cuddy, the round Bomar hatch on top of the cabin leaks between the aluminum frame and fiberglass deck... I am wondering what to use for sealant. I've read, butyl sealant, 3M 4200 sealant, Dow 795, etc...
  7. G

    Stingray Transducer Mount Question

    Suggestions on where to mount the transducer so I don't lose readings on plane..
  8. G

    Safe Hull Cleaner Recommendations

    Looking for a boat hull cleaner that is also safe for my painted Eagle trailer.. Don't have alot of grime, some discolored hull & water line from being in the River for 2 weeks.. I tried one product, "biodegradable", it worked on small area, but noticed it discolored a diamond plate trailer...
  9. G

    Faria Depth Sounder

    Faria depth sounder on new to me 2013 Stingray 215CR, worked for 2 days in water, now it blinks 00 or gives wrong readings. Found transducer in the bilge, I'm assuming its a "in hull"...On vacation, need a depth sounder... Checked connections and seem OK. Any suggestions besides going to marina...
  10. G

    Replacing Reverse Lockout Solenoid Help

    I need to replace my reverse lockout brake solenoid on my 2010 EZ Loader trailer. Where it's located the bottom frame is open and I may be able to get a wrench on the brake hose fitting. Question how do I remove the brake hose without it getting twisted? It seems to run the length of the trailer...
  11. G

    Threaded Post Came off With Spin On Fuel Filter

    2010, 3.0 MPI. I removed the spin on water separator/filter and the center threaded post came off with the filter. It's threaded in the housing,smaller thread,& had some sealant on it. So do I put some type of sealant on the threads(Permatex red thread lock or Form-A-Gasket 1) and screw it...
  12. G

    Merc Alarm After Disconnecting Sensor

    So in order to check the accuracy of my single wire temp gauge/sensor I also disconnected the 2 wire "Digital Coolant" sensor next to it, so I'd have more wire. Now when I turn the key on instead of a short alarm I get a long one and while leaving the key on I also get one beep...Will this...
  13. G

    Accuracy Of Temp Gauge

    My temp gauge is off by about 25 degrees since new 3 years ago.. Checked with 2 Infrared digital temperature meters at the sending unit/thermostat housing... If I change the sensor or gauge will that "maybe" help?? Or just live with it...
  14. G

    Upper Drive Housing Won't GO Last 1/8"

    Re installing Gen 2 drive and have a 1/16 to 1/8 gap between the upper housing assy and bell housing assy. Just wont go the last fraction. Thinking that it's the large rubber "O" ring keeping it out?? Correct ?? Thanks...
  15. G

    Rubber Washer on Lower Shift Shaft

    There is rubber washer, 12-77674, just above the oil seal for the lower shift shaft. How is that positioned on the shaft, do I push it against the seal or let it set half way on the shaft?? Alpha Gen 2 Thanks
  16. G

    Alpha Water Tube Alignment/Assembly

    Re: Alpha Water Tube Alignment/Assembly Yes the one replacement gasket has a strip of rubber on it, but nothing like this... parts diagram show 2 gaskets and plate
  17. G

    Alpha Water Tube Alignment/Assembly

    After installing new impeller assy, Alpha 1 Gen 2, when setting drive housing onto the gear housing, how do i know if the water tube that goes into the upper drive housing is lined up & correctly in the O ring & do I replace that O ring (#88393) also?? Also do I use 2-4-C on impeller blades or...
  18. G

    Installing Alpha1 Gen 2 Drive Needs

    What other items do I need, when re installing Alpha 1 Gen2 drive, for gasket /O rings/splines. Such as sealants, glue, grease type ? Is everything on the video?? http://forums.iboats.com/mercruiser-i-o-inboard-engines-outdrives/mercruiser-...os-590378.html Thanks
  19. G

    Transom Switch

    Installing a transom trim switch, and do I need to put sealant around the switch, and if so what?? There is a small gasket on the switch itself but not around the perimeter...
  20. G

    Replacing Alpha Impeller the LI Way

    This video makes it look easy... Replace Sea Pump Impeller on an Alpha - Part 1 - YouTube Replace Sea Pump Impeller on an Alpha - Part 2 - YouTube
Top