Search results

  1. Theoutdoorsman

    1979 Evinrude 140 rebuild sucessfull start but problem......?

    Fired this rebuild up today for the first time. Was surprised to see it start so quickly!!!! While running, I noticed a small water leak coming from the tale tell nipple coming out of the exhaust housing. Got that problem fixed right away. After restarting, I noticed the lower cowling still had...
  2. Theoutdoorsman

    Flywheel key on 1979 Evinrude 140...........?

    When I purchased the flywheel key, it had two small indentions in one side kind of like from a puch or something. Is this normal, or did i get a defective key?
  3. Theoutdoorsman

    Ready to go.........1979 Evinrude 140

    Just completed the installation of the temperature sensors and replaced the head covers. Is there a waiting period required to allow the gasket sealing compound to set up, or can I turn the key on my rebuild right now? Thanks..............ALAN
  4. Theoutdoorsman

    1979 Evinrude 140 Shift rod adjustment?

    After pulling the lower unit to replace the water pump it won't shift into reverse. Long story how this happened. Let's just say it was a "stinging" experience....... d:) ........ and I turned it. Which direction do I need to turn the adjustment to correct this problem after I pull the lower...
  5. Theoutdoorsman

    Teleflex temperature sending unit?

    I'm looking towards adding a Teleflex temp guage to my newly rebuilt 1979 Evinrude 140, model number 140983. What I would like to do is, check the temps on the powerhead on both sides individually by switching between two sending units via toggle switch or otherwise, one on the starboard and one...
  6. Theoutdoorsman

    1979 Evinrude 140. Just about ready for break-in!!..........?

    Is there anything that I should be especially concerned about before turning the key on this rebuild? Anything to keep a close eye on which might reflect a problem? A new water pump has been installed along with thermostats that were non-existant prior to the rebuild. I am assuming the water...
  7. Theoutdoorsman

    Misplaced the flywheel key.........now what?

    Can anyone help me in locating a replacement flywheel key for a 1979 Evinrude 140?....... P/N: 307480
  8. Theoutdoorsman

    1979 Evinrude 140 spark plug?

    My service manual suggests using Champion UL-77V permanent gap plugs. I recall being advised to, instead, install Champion QL77JC4 plugs gapped to .40. Would you guys agree? Why, if you don't mind my asking? Thanks................ALAN
  9. Theoutdoorsman

    Testing temperature switches?

    Can I effectively test my temp switches on my 1979 Evinrude 140 via an ohm meter? When I took the head covers off and removed them, they appeared to be in great shape. Thanks.........ALAN
  10. Theoutdoorsman

    '79 Evinrude 140 water pump kit installation?

    How difficult is it to drop the lower unit and exchange the water pump with a new kit? I've finished rebuilding the powerhead and need to get this done ASAP so I can begin my break in next week while on vacation. Any advice or helpful tips would be much appreciated. Thanks..................ALAN
  11. Theoutdoorsman

    1979 Evinrude 140 carb orifice plug adjustments?

    I was wondering if anyone could lead me in the right direction concerning the adjustment of the jets in my carbs. The service manual, to the best of my knowledge, doesn't elaborate on this. Do I simply screw the jets back in snug and go, or is there a proper means of adjusting them? If they are...
  12. Theoutdoorsman

    1979 Evinrude 140 Missing Thermostats?

    While servicing the powerhead, the service manual suggests replacing the thermostats. Upon removing the cover, and to my surprise.............no thermostats were installed!!! How likely is it, that this may have contributed to the failure of the powerhead? Until now, all I can say is, carbon...
  13. Theoutdoorsman

    1979 Evinrude 140 carb rebuild?

    Is it possible to remove the high and low speed orifice plugs without the need of the special tool mentioned in the OEM Service Manual (p/n 317002)? Also, is it mandatory that the core plugs be removed on the carbs or can one normally get by without removing them so long as the carbs get a...
  14. Theoutdoorsman

    Crank case flange preperation?

    Is it acceptable to clean and prepare the crank case flange with alcohol prior to applying the anerobic gasket maker? Or is the OMC Safety Solvent a MUST USE product? Thanks.................... ALAN 1979 Evinrude 140
  15. Theoutdoorsman

    Here's a really dumb question.............

    Does anyone else here ever feel like their part of a Bill Dance blooper video....... 8) ........... Will starter fluid kill these things? I'm out of wasp spray and really don't want to drive to town right now. But more so, I don't want to be eaten alive by these things either...
  16. Theoutdoorsman

    1979 Evinrude 140 hp powerhead rebuild questions?

    Sorry to double post this question guys, but my other thread appears to be stagnant. Does anyone know of a trick to installing the retaining rings in the pistons without the use of the Special Tools Cone and Driver? Any tips or tricks would be much appreciated. Thanks in...
  17. Theoutdoorsman

    Question on 1979 Evinrude 140........

    This may sound like a dumb question, but, should I hear a beep when the key switch is turned which would indicate the overheat warning alarm is functioning properly? Just curious, this motor has never done this, and I hear it alot when other boaters are starting their outboards. I just want to...
  18. Theoutdoorsman

    Question for Joe Reeves.

    Can you post a link to your "link and sync" directions. I've been trying to locate it but am having some trouble finding it using the search feature. Thanks a bunch..............ALAN
  19. Theoutdoorsman

    Questions about rebuilt powerheads.........

    Should a slight difference in horsepower be expected with a .030 over piston change on all four holes. Just curious as to weather or not I might need to consider a change in prop size after this rebuild is complete. My current prop was turning about 5600-5800 rpm's, prior to pulling the...
  20. Theoutdoorsman

    1979 Evinrude 140 rebuild..........almost ready !!!!!

    As of right now my block, crank, and head are sitting at Mar-Fab in Sparta, TN. All four holes have been bored to .030 over and the block has been cleaned. The journals have been pollished on the crank and the bottom bearing has been replaced with a new one. The other two are going to be...
Top