Search results

  1. Theoutdoorsman

    1979 Evinrude 140 Trim Cylinder Seal Replacements

    Hi all. I have finally acquired the proper seals to repair the leaking trim cylinders on my 1979 Evinrude 140hp outboard model #140983. The part numbers acquired are: End Cap O ring: 319662 Wiper Trim Rod: 122494 Ring Backup End Cap: 321715 Trim Rod O...
  2. Theoutdoorsman

    Block boring question......?

    A friend of mine just purchased a boat and motor, only the motor on the boat was knowingly bad in that the top piston was toast. The numbers on the motor are as follows: Evinrude 60 hp 3 cylinder Model # TE60TLESM . From what I can gather this is a 1990 model. Once the head was removed, I...
  3. Theoutdoorsman

    Need some advice guys. I got a good scare Saturday.

    Well, I did the most ignorant thing I could have done Saturday. I ran my fuel cell dry and the motor came to an abrupt halt. When I went to back to prime the bulb, I found it was sucked completely flat. After finally getting the bulb to prime again, the motor is now acting sluggish. Now, it's...
  4. Theoutdoorsman

    Need some information on a couple of OMC props please.......

    I think I have found a suitable prop for my application. I tested the prop today and was very very very pleased with the performance. I am 99% sure the numbers on this prop read 384142. And I think it is a 13X19 pitch. Can anyone verify this? Also, is it possible to put a 1/2 cup on a prop. The...
  5. Theoutdoorsman

    CMC PT130 Jackplate installation........?

    My Evinrude 140 (1979) is nearing the final moments of the break-in period, following a complete powerhead rebuild. I am very seriously considering upgrading the tilt-n-trim unit to the CMC jackplate unit. Are there any things I need to look out for prior to the installation. I'm not certain the...
  6. Theoutdoorsman

    1979 Evinrude 140 leaky trim cylinders????

    Hey again all !!! With my newly rebuilt powerhead nearing the final moments of the break-in period, I am now turning my attention to the leaky trim cylinders. I wanted to consult with you guys concerning the replacement of the seals in the trim cylinders. Is it possible to remove the caps on the...
  7. Theoutdoorsman

    Hey Walleyehed !!!!!! Got a question for ya............

    Will a CMC PT-130 hydrolic jack plate withstand the power exerted by a 1979 Evinrude 140 outboard, or would you recommend something else? What things do I need to consider, in terms of cables and so forth, prior to the installation of a jackplate?
  8. Theoutdoorsman

    1979 Evinrude 140 venting at full trim at WOT........?

    Hey guys/gals.......... I have noticed, prior to rebuilding, that I was venting (or the prop sounded like it was coming out of the water) before reaching my full trim limit at WOT. Would it be correct to assume that I need to lower the outboard on the transom to prevent this in the future? If...
  9. Theoutdoorsman

    1979 Evinrude 140 lower unit gear ratio?

    Can anyone recall, off the top of their head, what the lower units gear ratio is on my 1979 Evinrude 140. I'll need this for future reference when determining my prop slip to complete my setup. Thanks a bunch !!!!.................. ALAN
  10. Theoutdoorsman

    A LETTER OF APPRECIATION.

    So far, I have followed the OEM service manual to a "T", and got some really great advice, tips, tricks, AND help from fellow iboats members. This was my first, ever, outboard powerhead overhaul and I've been really really patient, but anxious, to get her singing again. Today, I finally got to...
  11. Theoutdoorsman

    1979 Evinrude 140 Temp guage kit ?

    I found a complete kit on eBay and was just wondering if this kit would be suitable for my outboard. The sending unit is no longer available, or so the local dealer is telling me, for this year powerhead. Just curious if this "Z" clip guage will work effectively and accurately? Anyone have any...
  12. Theoutdoorsman

    Recent rebuild, no WOT????? (several pics)

    I am in the middle of rebuilding my carbs again on my very recently rebuilt 1979 Evinrude 140. So far, I haven't been able to get her past 2000 rpms since the rebuild and I continue to hear this annoying cough at an idle. Compression is at 110 all the way around and even. The link and sync was...
  13. Theoutdoorsman

    1979 Evinrude 140 Joe Reeves timing question.

    I checked the timing as per Joe Reeves meathod. With the exception of taking the plugs out. I simply wired the high tension leads to my home made spark tester and cranked the engine over and checked the timing to see where I was at. I was dead on 24*. The timing on my powerhead is supposed to be...
  14. Theoutdoorsman

    Need help with finding top dead center.........?

    Can someone explain, in detail, how I can make a piston stop so that I can be absolutely certain I'm not setting my timing wrong? Thanks a bunch.............ALAN
  15. Theoutdoorsman

    1979 Evinrude 140 rebuild sucessfull start but problem......?

    Fired this rebuild up today for the first time. Was surprised to see it start so quickly!!!! While running, I noticed a small water leak coming from the tale tell nipple coming out of the exhaust housing. Got that problem fixed right away. After restarting, I noticed the lower cowling still had...
  16. Theoutdoorsman

    Flywheel key on 1979 Evinrude 140...........?

    When I purchased the flywheel key, it had two small indentions in one side kind of like from a puch or something. Is this normal, or did i get a defective key?
  17. Theoutdoorsman

    Ready to go.........1979 Evinrude 140

    Just completed the installation of the temperature sensors and replaced the head covers. Is there a waiting period required to allow the gasket sealing compound to set up, or can I turn the key on my rebuild right now? Thanks..............ALAN
  18. Theoutdoorsman

    1979 Evinrude 140 Shift rod adjustment?

    After pulling the lower unit to replace the water pump it won't shift into reverse. Long story how this happened. Let's just say it was a "stinging" experience....... d:) ........ and I turned it. Which direction do I need to turn the adjustment to correct this problem after I pull the lower...
  19. Theoutdoorsman

    Teleflex temperature sending unit?

    I'm looking towards adding a Teleflex temp guage to my newly rebuilt 1979 Evinrude 140, model number 140983. What I would like to do is, check the temps on the powerhead on both sides individually by switching between two sending units via toggle switch or otherwise, one on the starboard and one...
  20. Theoutdoorsman

    1979 Evinrude 140. Just about ready for break-in!!..........?

    Is there anything that I should be especially concerned about before turning the key on this rebuild? Anything to keep a close eye on which might reflect a problem? A new water pump has been installed along with thermostats that were non-existant prior to the rebuild. I am assuming the water...
Top