Search results

  1. grizzreaper

    cobra gear oil

    good day everyone. i got new crush gasket and a new seal for dip stick. drained the oil from drive. i put the bottom plug in and tightened. left top plug out and dip stick out. now i am not sure if the bottom plug is like any other drain plug, but i looked for any metal or crap on the plug it...
  2. grizzreaper

    302 omc with cobra outdrive

    hello again everyone, i have a 302 omc in a 1988 bayliner capri. awhile i was having problems with the power, i have that fixed. thanks for everyone for all your help. i went to change the the thermostat and found there was none. i put the new one in with the gasket. no leaks when i put the...
  3. grizzreaper

    1987 bayliner capri 1950 cuddy with inboard 4 cylinder 3 litre omc cobra outdrive.

    hello i had my boat out yesterday, started a little rough.gave it some throttle n let it warm up a bit. noticed my temp gauge isnt working but oil,gas,and rpm is.not sure how to change temp gauge, but this isnt my main problem. we cruised around a bit felt grt. after 20 mins or so i gave it full...
  4. grizzreaper

    1995 9.9 mercury

    hey guys does a 9.9 mercury have a charging system. if it does can someone show me a wiring diagram. it is a pull start and tiller controled. thanks in advance
  5. grizzreaper

    gale buccaneer

    not sure on the spelling the gale bucc but my friend found trhis motor in his parents basement and his mom wants to sell it. we are looking for any info on it. its a model 3d-19b and serial 363381 any and all help would be grt. thanks in advance
  6. grizzreaper

    merc mark 2

    hello guys i was wondering if anyone can help me with this motor. i think the serial number is 956207 and it is a 4 or 5 hp. a friend of mine found these in his parents basement. his mom wants to sell them but would like some info on it. thanks in advance. he founf five old motors in the...
  7. grizzreaper

    old motors

    hey guys i have a few motors that a friend of mine has found in his parents basement. one is a johnson sea horse n i believe the serial number is 54216 model td 20 . another johnson model md-ao12 n serial number 267362. any info on these two motors would be grt. there is two more motors too...
  8. grizzreaper

    71/72 50 evinrude with eletric shift

    hey guys i think this is a stupid ? but here goes anyway. do i need to keep the battery hooked up once i have the motor running to switch gears. thanks in advance
  9. grizzreaper

    1972 50 hp evinrude elctric shift

    hey guys where can i find a wiring diagram for my motor. it doesnt seem to keep my battery charged and i found two purple wires that have been cut. there is a diagram in the motor but its worn n not readable. also how hard is it too rebuild the carb. motor runs ok but a lil shaky and wants to...
  10. grizzreaper

    what gear lube do i need.

    hello everyone i just picked up a 71 or a 72 50 hp evinrude model model 50172s and would like to know what type of gear oil do i need to use. any help would be great. thanks in advance.
  11. grizzreaper

    1957-58 Johnson- Evinrude outboard motor 35hp

    hello i was wondering if a mercury shifter and throttle control will work with a evinrude motor.any help on this would be great. thanks in advance paul
  12. grizzreaper

    1975 40 hp 402 thunder bolt

    hello everyone i just swapped a stator rectifier and choke selinoid from one motor to another. i am not getting a spark . i looked at 402 wiring diagram and did it the way the diagram said. there is no kill switch all done by key on the shifter control. my problem now is i have a extra wire...
  13. grizzreaper

    1975 402 thunderbolt merc 40 hp

    i was wondering if i could interchange my motors. i have a long shaft merc and a short shaft merc both the same year and hp. my transom is not quite 19 inches. i see that 15 to 17 inches is for short shaft and 19 plus is for a long shaft. could i get away with the short shaft or should i swap...
  14. grizzreaper

    1975 402 40 hp mercury

    hello hope someone can help me with two things i started my motor and a cant seem to get it to stay running. it smokes really bad and chugs sputters and jumps around. i put fresh gas in i was told 50:1 oil mix. i did remove the fly wheel and stator but i did mark it before removing. i think...
  15. grizzreaper

    1975 mecury 40 hp 402

    i was wondering if anyone can help me find a schematic or diagram of the location for the choke solenoid, starter soleniod and rectifier on my 75 merc 40 402 thunderbolt.
  16. grizzreaper

    trying to wire a 75 mercury

    hello i am trying to wire my electric 40hp 402 1975 mercury . i have tested the starter and it works. i have noticed there is no starter solenoid or a choke solenoid. now i was thinking of just wiring three postion switch to the starter but not sure if i will do any damage and if it will keep...
  17. grizzreaper

    what kind of fuel connector do i need

    i have never seen this type before. always had a evinrude with two ploe connector for the fuel line. i seen my 95 9.9 mercury has the sorta same as the evinrude but the 40 has a insert. is this a bayonet styke of a connector or do i need some special one. thanks in advance .
  18. grizzreaper

    fuel/oil mix

    hello i have a 1975 mercury 40 hp 402 and i was wondering what the fuel mix is. is it 50 : 1 and i also have a 1995 mercury 9.9 will that be the same mix thanks in advance
  19. grizzreaper

    1975 mercury 40 hsp 402

    hello this took awhile to figure out how to post this so here goes lol. i picked up a 15 ft tempest with 1975 mercury 40 hsp 402. i am trying to figure how to hook up the eletric starter to the key switch. everything is there. i jumped the starter n it works but the guy said it needs a...
  20. grizzreaper

    1962 10 hp evinrude

    hello i want to know if a 1962 28 hp motor control will fit a 1962 10 hp evinrude . thanks inadvance for all and any answers.
View older results
Top