Search results

  1. R

    1998 Force/Mercury 120 HP - Good Motor?

    Site owners have mandated this !----I too feel they are wrong.-----But remember this is a site that looks at selling parts / manual.----Not wanting to carry a huge FREE information storage bank.
  2. R

    Johnson 115 track year model

    Sounds like a 1990 model.-----Reread model #------Simple and very good motor when it left the factory.-----Install a new water pump impeller before leaving the dock.-----Any boat shop will get you the parts I think.-----crowley marine -----evinrudeparts.ca----- and this site you are on.-----your...
  3. R

    Evinrude Tilt Trim motor

    No thanks ---I have lots of good drive couplings laying around.----Perhaps get your money back from seller?
  4. R

    Evinrude Tilt Trim motor

    There is only ONE DRIVE COUPLER.-----Perhaps one of the check valves is stuck.-----And no it does NOT need to be installed on a motor to see tilt and trim rams moving to their limits
  5. R

    Evinrude Tilt Trim motor

    The tilt cylinder might need to retract all the way BEFORE trim cylinders move. !
  6. R

    Evinrude Tilt Trim motor

    After the tilt cylinder goes to maximum extension , the trim cylinders may start to move.----Sounds like you need to contact the seller on this trim / tilt unit.
  7. R

    Have spark and fuel, can't get the rebuilt engine to start

    Not an expert here, but is there a mix up with left hand / right hand rotation parts ??
  8. R

    1975 Johnson 25 won't run above idle in gear under a load.

    Some simple inspections to do on your part.
  9. R

    1975 Johnson 25 won't run above idle in gear under a load.

    ????-----" forward gear won't go above high idle "----That statement could mean different things to different people.----Could be many things to check.-----Motor might be running on 1 cylinder for any number of reasons.------I should refrain from giving simple advice on this one.-----Stepping...
  10. R

    1975 Johnson 25 won't run above idle in gear under a load.

    Maybe the propeller is slipping ??
  11. R

    Info on Evinrude 115 E115TLETS

    When they assemble a new motor is with hundreds of tested / inspected parts.----No different when you are inspecting / refurbishing a motor that is 30 years old.
  12. R

    Suggestions rebuilding a Bowrider

    You are looking to build a bow like in the pictures for your own boat?
  13. R

    1956 Fastwin 15 Drive Shaft and Impeller Issues

    The pin at the top of the driveshaft rotates / drives the seal assembly.
  14. R

    1956 Fastwin 15 Drive Shaft and Impeller Issues

    ????----On the 5.5 HP there is a hole for a pin / key to drive the impeller !------Not possible to install driveshaft upside down on a 56 model 15 HP.
  15. R

    Confused New Owner of an Old Boat

    Looks like it had water in it and froze.------Gear housing needs to be replaced.
  16. R

    Confused New Owner of an Old Boat

    That is correct.----A GM inline 6 model.------Many ( not all ) had issues with structure under the floor.----Boat appears to have been looked after.
  17. R

    Info on Evinrude 115 E115TLETS

    Start another --" oil thread "----On the fundamental difference between TCW oils and oil meant for direct injection engines ?
  18. R

    Info on Evinrude 115 E115TLETS

    I see post #17----I am not sure why the comment about---" Absolutely makes an injector oil " ----is even in that post.-----I am just curious as to what is meant by that comment
  19. R

    Oil coming out of carburetor

    See post #10
  20. R

    Info on Evinrude 115 E115TLETS

    Not sure why this was mentioned in post #17.----The statement does not make sense to me.
Top