Search results

  1. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    Yes. I have fixed this issue and there is not any water in the u-joint bellow any more. It is very clean. I have just taken a photo inside the bellow
  2. L

    Can the base of engine work? Two to bolts under engine are rusted and can

    Yesterday I went fishing and it run good about 30miles at the beginning, but 8 hours later it run very slow wit the speed not more than 10 miles and I have noticed the engine is a little bit hot. and I did run at my driveway when I got home. You can see my running video at following link. Can...
  3. L

    exhaust bellow off again

    But I do not know why my boat slow down after the exhaust bellow came off. Is it possible that broken bellow has changed the water flow direction and lead to the slow down of the boar?
  4. L

    exhaust bellow off again

    But the water comes out from engine while motor runs
  5. L

    exhaust bellow off again

    I have just resealed the exhaust and u-joint below two week ago. nightmare. Is exhaust bwllow mandatory? Somebody mentioned it us full of water while boat is in the water. my boat is Mercruiser 1989 2.5l 120 hp
  6. L

    exhaust bellow off again

    Last friday my boat had the maxium speed of 33m and yesterday it run very slow only 9m and I found the engine side of exhaust bellow was off and the outdrive side is still good. It seemed I lifted the outdrive too high. How can I adjust the trim limit & sender to make the outdrive not to be...
  7. L

    tricks to push outdrive in

    You are right. I mounted the propeller and then I turn the propeller and the outdrive is easy to be pushed. thank you.
  8. L

    tricks to push outdrive in

    How can I turn the engine coupler a little bit by hand?
  9. L

    tricks to push outdrive in

    Allignment tool is very easy to be pushed in and get out. Also shift lever and outdrive are in the forward postion. But they have not touched and the outdrive is stuck.
  10. L

    tricks to push outdrive in

    Today I tried to mount outdrive. but what a pity the outdrive was stuck. Sometime it is very difficult to puth Mercruiser outdrive in. sometime it is easy. any tricks?
  11. L

    What reason causes the water leaking into gimbal bearing house?

    The shaft house seems good and there is not water any more after I apply the big o-ring. At the beginning at the water, my boat can reach maximum speed of 33 mile. But after 8 hours in the water and it seems that slow down. Any reason?
  12. L

    What reason causes the water leaking into gimbal bearing house?

    Where is the the gimbal bearing house's drain hole located? it should drain the water if it works
  13. L

    What reason causes the water leaking into gimbal bearing house?

    There should be one small hole on the gimbal bearing and the hole should be put at the bottom while it is mounted, then any water leaking into the bell house can leak into boat through the hole and the outdrive can be protected. I did find there is a small hole on the gimbal bearing. Is my...
  14. L

    What reason causes the water leaking into gimbal bearing house?

    I have sealed it. Thank you.
  15. L

    What reason causes the water leaking into gimbal bearing house?

    I still have some. which side should I glue with it? engine side or outdrive side?
  16. L

    What reason causes the water leaking into gimbal bearing house?

    What kind of glue do you suggest? Could you please give me a link or pict? Thank you
  17. L

    What reason causes the water leaking into gimbal bearing house?

    Do you mean it should stop leaking into gimbal beating house if I apply the big o-ring rubber?
  18. L

    What reason causes the water leaking into gimbal bearing house?

    Hi Alldodge and Scott, Can the big rubber o-ring prevent water leaking into gimbal bearing house if the outdrive gasket is good and the bellow works? if so I will do a testing tomorrow.
  19. L

    What reason causes the water leaking into gimbal bearing house?

    Hi Scott, Can the big rubber o-ring prevent water leaking into gimbal bearing house if the drive gasket is good and the bellow works? if so I will do a testing tomorrow.
  20. L

    What reason causes the water leaking into gimbal bearing house?

    Can Scott help me identify what parts were missing for the shift shaft? I am cencerned water leaking from it?
Top