Search results

  1. J

    Lift pontoon boat by decking?

    From experience this past spring...and the marina that had to buy me two new toons: any lifting/supporting on the toons themselves should only be placed at the seams between the toon sections , and at the stern end cap. The boat itself can be supported and lifted on the joists but you want to...
  2. J

    Sylvan 2012 8522LZ - Add a Porta Potti?

    Unfortunately, I can't see what you have (and vice versa) because pics can't be uploaded. I added a porta potty to my '06, 24' lowe pontoon in my changing room. My 4 uprights collapse into themselves but are parallel to the base top rail. So nothing extends down to hit or prevent putting a porta...
  3. J

    Best Bumper Type and Size for Pontoon

    I have a 24', 25" diameter pontoon. I I use the cylindrical bumpers, mainly two per side, 3 if I need it, but seldom do. My clamp slips over the railing, the rope disengages with a tug , so moving the bumper up or down is easy. Plus the clamp is just sitting on the rail so it also can be moved...
  4. J

    Pontoon Trailer

    every pic I see shows that boat on a single axle.
  5. J

    opinions..pictures

    clarefication: I'm a gearhead but incapable of engine swaps, rebuilding, etc. No space, therefore no equipment for that. I did remove and install a tranny in a '72 monte, and a '92 aerostar (twice) in a carport on my back. By myself. Bolt on's also ok....but beyond that, nope. and waiting for...
  6. J

    opinions..pictures

    ok...so, it could still be the mpi?.... if it is carbed, would you walk ? 300 vs 260 is one thing , but 300 vs 220 is significant. a water test is mandatory..
  7. J

    opinions..pictures

    I'd have to check. um, using my gear head knowledge, the air filter sits on top, like a carbureted car....no hose to an airbox. It wasn't an in depth pre purchase, just stopped to look as it was on my way to my marina. A couple of "flags". boat has been on the market for a while. I know because...
  8. J

    opinions..pictures

    It a 240 sundancer, so I know some think that's kinda low, but It just mainly would be 2. Maybe rarely more. there is a grayish/tanish semi crusty discharge showing around the water inlets on the lower case.. Wouldn't know if that's normal or not. The manifolds have been replaced. The reason...
  9. J

    opinions..pictures

    I understand that. Which is why you hire an inspector. But there are people on here who have been around boats for eons and are capable of offering valid opinions just by looking. still can't ad pics, so doesn't matter .
  10. J

    opinions..pictures

    hmm...can't add pics
  11. J

    opinions..pictures

    The outdrive is a bravo 3, on an '06 sea ray. supposedly 300 hrs. Not many pics, I know but couldn't see any other areas to question. engine (5.0) compartment is very clean, well maintained....there are no grease, rust or oil stains. So , see anything ? good/bad.
  12. J

    Changing props. What one to get?

    that has not been my experience. Same boat, load, conditions. Regardless, speed was 3 mph lowest to highest.
  13. J

    Changing props. What one to get?

    assuming nothing is wrong...including a waterlogged boat, as implied. You didn't say what you are trying to do. props aren't miracle workers. You can fine tune, but usually trade speed for torque. Your 800 rpms from max WOT. So you can drop 1 inch in pitch and get the rpm's to 5300+/- ? , at...
  14. J

    need a new prop ?

    I can't tell you specifically what you may need. That's going beyond my knowledge. I don't know what props fit that motor, or if yours does. My thrust washer only fits one way as it has a beveled hole to match the shaft bevel. My thrust washer has a flat that fits into the plastic prop hub, so...
  15. J

    Best way to gain a little speed with 40hp engine

    just because a tach has a 7000 rpm range, that's not an engine's rated limit.
  16. J

    karavan sure lube axles, nice.

    It is not, I agree. My grease , however, didn't turn to muck. The water was actually separate from the grease. Pushed it out and made drops of water. Maybe it's the grease I use and I have researched this stuff like crazy. Also maybe it's my maintenance as it gets a fall and spring shot and ...
  17. J

    Best way to gain a little speed with 40hp engine

    oh yeah...go fast, burn gas. I wonder if enough air could get under that toon and flip it at speed.
  18. J

    karavan sure lube axles, nice.

    Sure lube axles on my dual karavan trailer really make maintenance easier. I trailered my pontoon from the chesapeake bay slip I'm in to Lake Raystown in Pa. So multiple dunkings. Got the grease gun out at home before heading back to the slip and was able to force the water out of each spindle...
  19. J

    Best way to gain a little speed with 40hp engine

    so if your max throttle rpm is 5500, at 5300 you're kinda there. ya wanna go fast? Get one of these. lol
  20. J

    Best way to gain a little speed with 40hp engine

    propping...It depends...and can get expensive.....I'm not one to steer anyone to a particular prop or what exact pitch you have to get. I can give you what I've learned and experienced. Engines have an operating rpm range, my mercs are 5-6000. You need that knowledge, After getting my new 115...
Top