Search results

  1. 04fxdwgi25

    Help me identify whether I have a 1" or 1 and 1/8" shaft

    Instead of guessing, get a cheap vernier caliper. Available anywhere, such as True Value for under $20.
  2. 04fxdwgi25

    helm wiring, should be simple, i'm not too bright.

    Revert back to post #9 or get a friend (or someone qualified) that understands basic marine / automotive wiring to help. Mistakes can be costly by allowing the magic smoke to escape and turning you project into a cinder.
  3. 04fxdwgi25

    helm wiring, should be simple, i'm not too bright.

    Did you put fuses in the slots? Sounds like you are just reading through the fuse blown indicator diode.
  4. 04fxdwgi25

    No spark thunderbolt 5.

    TB 4 and 5 manual. Has trouble shooting guide in it
  5. 04fxdwgi25

    Just keeps going right

    Is there a larger trim tab available for the engine you didn't name?
  6. 04fxdwgi25

    Pressed-in Zerk grease fittings

    Have been known to tap a tread into those holes and screw in a threaded zerk
  7. 04fxdwgi25

    Mercruiser Exhaust Tube vs Exhaust Bellows Opinions, and Part # for Tube.

    Only downside of the tube is that if your engine doesn't run correctly (rich / lean or burn some oil), the tube will allow a film yo form on drive unit and the rear of the boat and a very slight increase of sound. Whereas the bellows directs it all thru the prop. The 4 cyl probably will sound a...
  8. 04fxdwgi25

    7.4 merc won't start after winter storage

    You are right, but the later model Gen GM motors don't have a fuel pump boss / drive, as everything went to electric fuel pumps in the auto world.
  9. 04fxdwgi25

    Installing a transducer in an aluminum boat

    Have mounted a chunk of Starboard to transom of older boats and then mounted the xducer to the plastic. Never had a problem.
  10. 04fxdwgi25

    A-team HEI distributor upgrade shift interrupter wire connection

    79 bux for a complete HEI distributor????? HAHAHAHAHAHA. No thanx.
  11. 04fxdwgi25

    MerCruiser Alpha One Gen 1 – Shift Shaft Alignment Reverses Forward/Reverse Gears After Impeller Install

    If you place it in forward gear (engine not running), the prop will free wheel, with clutch dog clicking loudly, when turned in clockwise direction. Don't know if I explained it to you clearly enough, but from what I think you are saying, sounds like yours is working correctly.
  12. 04fxdwgi25

    502 Mag MPI Performance Issue

    Have you checked your fuel pressure at different speeds? Sounds like pump isn't keeping up. Or, the fuel system supply has a problem, like a fuel line deteriorating internally, plugged tank vent, dirty fuel intake strainer or bad anti siphon valve.
  13. 04fxdwgi25

    Bravo Installation Kit ( ring gaskets)

    Looks like an Alfa/Bravo combo kit. Black one goes on the drive unit input shaft where it goes into the gimbal bearing
  14. 04fxdwgi25

    Fuel gauge pinned full w/o power

    I have seen some gauges that stay at last known position when powered off. Think his best option is to power it up and go through the troubleshooting scenario's to find out what is really happening. Anything else, is guessing.
  15. 04fxdwgi25

    Fuel gauge pinned full w/o power

    ^^^^^ Like he said, disconnect the pink wire from gauge (as shown in the instructions sheet I attached in my 1st response). If it goes back down, then you have a short in the wiring or the tank sender. If it stays at full, your gauge is kaput.
  16. 04fxdwgi25

    Fuel gauge pinned full w/o power

    Here ya go. You need to do some troubleshooting:
  17. 04fxdwgi25

    Oil Pressure Alarm

    Sometimes the float in the gear oil bottle gets goobered up and gives constant alarm, even when full. 3 possibilities: Lube oil alarm Oil pressure alarm High engine temp. All 3 are the same alarm with 3 sensors in parallel. Disconnect one at a time to see if goes away.
  18. 04fxdwgi25

    Oil Pressure Alarm

    I would install a cheapie ol mechanical oil pressure gauge in a "T" where the oil alarm sender sits, pull the spark plugs and spin it over with the starter. That'll tell you if you have oil pressure / wiring problem or not and if it's just a bad sender or a bigger problem.
Top