Search results

  1. Tarzan13

    Slide hammer puller

    PB Blaster is supposed to be the best for aluminum will try to find some I usely use Prolab 100 Thanks for the replise alot more informed then i was this morning will show pics of results
  2. Tarzan13

    Slide hammer puller

    Ok so I need to put something to loosen the corrosion any brand would be better for aluminum cast or is it the same as with other metal Thanks
  3. Tarzan13

    Slide hammer puller

    It going to be driving in both fresh and salt water….so that part doesn’t hold a seal it just protection for the seal? Can I run safely without it? If not I will buy that part The last owner did run without it the shaft was full of carbon crud where that part is supposed to be The boats from NFD...
  4. Tarzan13

    Slide hammer puller

    Those 1 of the 2 seal goes in that part?
  5. Tarzan13

    Slide hammer puller

    This is what was behind the propeller bushing assembly in this pic i have removed the tabs only the anode bearing housing should be right there or am i wrong
  6. Tarzan13

    Slide hammer puller

    Him missing the anode bearing housing thats why it look different there are screw hole in the housing with nothing in them
  7. Tarzan13

    Slide hammer puller

    1990 cj48eslesa Pls tell me what book you have so I can buy i
  8. Tarzan13

    Slide hammer puller

    1990 cj48eslesa Pls tell me what book you have so I can buy it
  9. Tarzan13

    Slide hammer puller

    No they won’t be a problem its just they don’t exists in my service manual and the blown image of the parts supplier and the carrier doesn’t look like any that i have seen for that engine so i hope the seal and o ring i order will fit Will have to see! Thanks for your help guys
  10. Tarzan13

    Slide hammer puller

    Mines got tabs you bolt on the carrier to keep it in place haven’t seen does the n any books or video
  11. Tarzan13

    Slide hammer puller

    I can’t afford to break it It’s discontinued and the one that’s in there does look at all like the one in the part diagram would be very hard to replace or the one in it is a replacement part hard to tell when one book tell you this and another book tell you that!!! And everyone on video that...
  12. Tarzan13

    Slide hammer puller

    Thanks
  13. Tarzan13

    Slide hammer puller

    No just the seal Im getting water in the gear case but I think it from the top but if changing the top doesn’t stop it will have to do the bottom but I see videos of people trying to remove the drive shaft bearings housing assembly and its a horror stories Hope not cause I need to change the...
  14. Tarzan13

    Slide hammer puller

    I need to remove my retainer bearings housing on my 1990 48hp can I use a slide hammer puller to do it or is it to much dont want to buy another puller for a one time shot want to use what i got Thanks
  15. Tarzan13

    Johnson 1990 48 hp spl service manual

    Found one on ebay that got the 93 in it would good for mine I guesd
  16. Tarzan13

    Johnson 1990 48 hp spl service manual

    I don’t know if im in the right discussion room but Im looking for a service manual for a 1990 johnson 48 SPL where can I buy one on the net download version Found some on ebay but they dont tell the year only the hp Found seleco but they got model J48ESLESA and VJ48ESLESA mine is CJ48ESLESA...
  17. Tarzan13

    Johnson trim/lift assist cylinder

    Pipe wrench already tried won’t move now I spray it morning and nidht with penetrating fluid prolab100 and cheques it with pipe wrench every day will drill a 7/16 hole on the and tap and put a7/16 bolt and try a pull it out with slide hammer puller or weld a long nut on the end and try turn it...
  18. Tarzan13

    Johnson trim/lift assist cylinder

    Yes it a 1990 48 Are those cylinder pressed sealed or we can open them like a regular hydraulic cylinder and get too the piston cause if its not sealed I can bring they seal and o-ring and have them matched from my supplier at the shop where work but I can’t touch anything till I can get a new...
  19. Tarzan13

    Johnson trim/lift assist cylinder

    Yes the lever is there and turned towards the back of the unlocked but the cylinder is leaking so it doesn’t assist me at all its just like a damper now it slows the speed I can lift the motor and it just making it worse How can I had oil to it I it will probably help it would work like a...
  20. Tarzan13

    Johnson trim/lift assist cylinder

    If I run with the cylinder removed unlocked at high speed will it go back and foward and break something or be dangerous?
Top