Search results

  1. harringtondav

    oil leak on 3.0

    I'm pretty sure this will work. $16 at Advance, $20 at AutoZone. Includes gasket and crank seal. ...or you could buy OEM: "Replaces: GM 3992251 and Mercruiser 59341A1. SKU: 0014-058. $114.99" I Googled "GM 3.0L gas engine timing cover". Thinking back ,I think I was super careful to not tear the...
  2. harringtondav

    oil leak on 3.0

    I had the outdrive removed to replace the prop shaft. So yes. It is not that much trouble, and good to do regularly to inspect the drive shaft bellows, U joints, gimbal bearing etc. For Mercruiser, shift to full FWD, disconnect the speedo pitot pickup, remove the rear trim cylinder pins, remove...
  3. harringtondav

    oil leak on 3.0

    I replaced a timing cover for a neighbor's son's 3.0L Cobra. It's been a while but I think I purchased an automotive cover. It took a while to find a GM auto application, but the cover worked. BTW, per @Bondo the cover had a rusted hole in the bottom. I first assumed it was the seal. Also I...
  4. harringtondav

    1/4" crown staples for bunk carpeting?

    Sorry. My reply was too wordy. "Does it mean that if 1/2" wide staples are placed 4" apart, then space the 1/4" wide staples 2" apart?" is what I meant to say. Also I agree with your notion that air pressure with 1/4" crown staples may need to be reduced. ...I've had to do this. Test with scrap...
  5. harringtondav

    Water in the bilge

    I have a 1 yr old boat. I always get some drainage from the bilge plug. ....as I did with my previous boat. Rain through the cover. Condensation. Splash from waves/wake, leaking raw water clamps/plugs, drainage from swimmers, etc. Don't worry until it pees more than a quart for no good reason.
  6. harringtondav

    1/4" crown staples for bunk carpeting?

    I used the SS 1/4" crown staples shown below when I re-carpeted my previous boat. 5/8" length seemed good since I had to wrap carpet around the ski locker under deck and didn't want them poking feet. These worked fine for the boat and a bunk re-carpeting job. As far as retention vs. 1/2", reduce...
  7. harringtondav

    Water stains

    Assuming you have a fiberglass boat, acid is the cure. ...Not so green, but effective. Above recommendations like toilet bowl cleaner and others contain acid. Muriatic acid is available in any hardware store. It's basically hydrochloric acid. But take care, it's mean stuff. Dilute 1/4 muriatic...
  8. harringtondav

    Faria Gauges

    I've only had two issues with Faria gages on two boats over 26 years. The first boat's tach would climb to a false high rpm during a cold start. ...two taps with my knuckle would fix it, and it then worked fine. New boat's pitot speedo showed 22 mph with the boat on the lift. Warranty, but I...
  9. harringtondav

    Hull ID Number Location on pre-1972 boat - Pacemaker

    HID's, and maybe serial numbers can be in locations other than a transom badge. Mine has another badge in the engine bay, and I just discovered a third behind the dash gage panel.
  10. harringtondav

    determining trailer hitch height

    Keep in mind this will increase the 'effective' tongue weight on your receiver. It looks like you have plenty of truck for that boat, but it may make the receiver squat a bit more.
  11. harringtondav

    determining trailer hitch height

    Same here. With my last two boat/trailers I level the trailer frame. ...then I fuss with the bunks as much as possible to get the boat as low and level as possible on the trailer.
  12. harringtondav

    Interesting Learning about Regal Dash Wiring.

    I just installed a new GPS speedo. I flubbed the first try. I saw what I thought was a spare purple B+ wire, so I ran it directly to the speedo. Oops, This was the feed at the trim gage which fed the rest. So all other gages had no feed, including the tach. No start. No Faria speedo self check...
  13. harringtondav

    In dash GPS speedo?

    Yea, my pal bought a generic in-dash GPS speedo to replace his kaputt pitot. I told him prepare to be humbled. ...he's always been a bit of a wind bag topper, so I reckon he'll still lie.
  14. harringtondav

    In dash GPS speedo?

    I agree. ...you or someone else mentioned this above. We're 100% on the Mississippi river. Always current. If I want to split hairs I can drift and get my handicap . ....This time of year about 2-3 mph. Either way it will be better than the original pito speedo. It shows 20 mph in the lift. When...
  15. harringtondav

    In dash GPS speedo?

    I just received this Faria Beede GPS speedo from one of their retailers. Faria tech help was great. I sent a pic of my dash and they gave me the correct model. I'd picked the wrong trim but they set me straight. Cloudy day, so I'm going down to the lift to install this.
  16. harringtondav

    How to tell a replacable hub prop

    Good to know, and thanks. I favor Solas props. ...in my price range, and seem to perform beyond their price. I purchased two as an upgrade to the VP prop that came on my new SX drive. ...thinking I missed the boat on the Rubex option since I can only put one prop at a time on the drive. ;). Good...
  17. harringtondav

    How to tell a replacable hub prop

    From what I know each prop manufacturer has their own loose hub design. I don't think there is much interchangeability. Our Mississippi River boating eats props, so I generally use aluminum to spare the prop shaft. I once bought a loose hub prop since the replacement prop is less expensive than...
  18. harringtondav

    Does VP go nuts on revisons and models vs. Mercrusier?

    Previous 25 yr old boat was Merc 4.3LX/Alpha II. New boat is VP 4.3V5/SX. I love the simplicity of the Alpha drive. I'm fully tooled for any repair. But the VP 4.3 had too many advantages over the Merc 4.5.: GM based 4.3 vs homegrown Merc. Closed cooling, VVT, high pressure direct fuel...
  19. harringtondav

    How do I Stop Loosing Bearing Buddys??

    This is my first thought. Some sizes are w/in .030" of others. A correct size BB requires a fair amount of heavier tapping to seat. ...interference fit. Check the chart in the link below to verify your size: https://www.bearingbuddy.com/model-selection
  20. harringtondav

    Merc Alpha style prop nut retention for VP SX?

    Merc Alpha Gen II for 25 yrs. VP SX for one yr. I prefer the Merc prop nut retention system. You'd think a simple SS cotter pin would be easier. Not for me. I carry a spare wheel and locking hardware in the boat. Now I need a needle nose pliers. ...same prop nut wrench as I used on my Alpha. I...
Top