Search results

  1. harringtondav

    Fitting my Bunks to my boat

    I agree with Grub above. Best practice is for your transom to be inside/forward of the bunks. ....Having said this, my current and previous Shoreland'r Equiload trailers are two bunk which have worked fine. But Shoreland'r bunks are fully adjustable which allowed me to get the rear of the bunks...
  2. harringtondav

    Boat Ramp Etiquette

    It's been written...sorta. Australian boaters FB group. Carnage on the Boat Ramp. I joined. Lots of laughs. https://www.facebook.com/groups/2152747564940504/
  3. harringtondav

    Boat Ramp Etiquette

    The issue with the two ramps I use is the docks are short two sided river floats with room for one boat/side, and the ramp parking areas aren't large enough for one trailer lined up. So local protocol is the boat waiting at the dock gets the ramp. Any boat waiting for launch gets the next open...
  4. harringtondav

    Boat Ramp Etiquette

    The etiquette is simple. Following it depends on the individual. Responsible boaters follow it. Slob boaters could care less. I liken a ramp to a four-way stop. First boat to arrive at the ramp gets the ramp, either launching or retrieving. Everyone knows their position in the queue. If it's a...
  5. harringtondav

    In dash GPS speedo?

    I had to ponder over @jimmbo 's remark, but I get it. I'll be doing speed runs/prop slip checks in the Miss. River, so I'll take the data points up and down river, and average the results. Per my OP my pitot speedo was significantly different than my phone's GPS. So I reckon a GPS speedo will...
  6. harringtondav

    In dash GPS speedo?

    I've thought about a fuel consumption monitor, but no real need. We mostly boat between two Mississippi river L&Ds, 19 mile pool with plenty of gas docks. ...wondering if a consumption monitor could be programmed in $/mile. But at today's gas dock prices that would just be a wet blanket on the...
  7. harringtondav

    In dash GPS speedo?

    It sets at 20 mph, then rises from there, and drops back to 20. Per my other comments, I'll spring for a GPS speedo and be done with it. Pitot tube speed readings are a general indication of fast or slow.
  8. harringtondav

    In dash GPS speedo?

    The pickup is in the front of the lower gear case. VP. Unlike my old Apha II the tube disappears into the gimbal housing somewhere. I followed it up inside the dash, disappearing into the speedo gage. No room to work, so I'll have to remove the speedo gage to remove the tube/hose. I can then see...
  9. harringtondav

    In dash GPS speedo?

    Thanks. Seems I was also confused. I decided to do some self help and found the same Faria p/n. ....looks like I'm set with a drop in replacement. I'm away from the boat for a few days. After I verify size and existing wiring I plan to order this.
  10. harringtondav

    In dash GPS speedo?

    Very happy with our new Regal 1900ESX. Like most pitot tube speedos, ours is off by a mile. I recently whacked some debris and plugged the lower unit pick up hole. I removed the plug and got a nice stream of water, but the gage is stuck at 20 mph min. So I'm looking at tearing into a brand new...
  11. harringtondav

    How much trim?

    At idle you can safely drive the boat with the trim up and not damage the drive. Your prop will come out of the water and stop moving you before you get the drive too high. My previous Alpha II boat had a trim limit. I often overrode it when in shallow water. My new boat is a VP SX. No trim...
  12. harringtondav

    Bearing grease / water leaked out on rim

    The seal is pressed into the inside of the hub. It is supposed to ride on the largest, inside diameter if the spindle. Make sure that surface is rust free. If not try to polish it with 200-300 grit wet/dry paper. Bearings and seals are standard for any spindle size. If the bearings and races are...
  13. harringtondav

    Check your furnace filter

    I only know systems that have the filter at the air handler/furnace. None in the return air system upstream. Check you entire system for filter locations. Returns and the main air box. If your high limit switch is shutting you down you may have blocked air flow...return or supply. Make sure all...
  14. harringtondav

    When you guff your brand new boat....

    Thanks Manitowoc ;). The gel gave itself up easily with 250 grit wet/dry. I knocked of the ridges and rough shaped the wounds. Then kept going until the tape edges surfaced, and removed the tape. Then it was a slow, two beer process sneaking up on the final contour.
  15. harringtondav

    When you guff your brand new boat....

    New Regal B/R first time back on a new trailer. Low water and the trailer was too low. Bow slid under the winch butterfly roller. Roller yoke guffed the bow. Spectrum Gel Coat Patch Kit from iBoats. ...perfect match. Mask and Dremel the edges of the guffs to 90 deg. Spread the activated gel...
  16. harringtondav

    Impeller puller screw

    Good to know. We are on the upper Mississippi. We occasionally pump a little sand when beaching on a sand bar. I'll get a spare impeller, but hope I get some temp gage warning when it's due for replacement. If the pump isn't below the waterline, it's too close for comfort. Definitely looks like...
  17. harringtondav

    Impeller puller screw

    I'm prepping for a full summer with our new VP SX 4.3 250 hp. ...only got 20 hrs on it late last year. The OM states to carry a spare impeller and change it annually. I will. Apparently inboard impellers don't last as long as the outdrive impeller on my old Alpha Gen II. My pal changes three...
  18. harringtondav

    Rotten Boat Factory

    Riverfront properties are as scarce as hen's teeth in our area. And most are on leased land. ...we own ours. The eyesore is a small price to pay. Besides, the owner is a lightening rod for all the neighbors to complain about. If it wasn't him it would be someone else.
  19. harringtondav

    Star Craft Acrylic windshield replacement

    FYI the link below describes the differences between Acrylic and Polycarbonate. We chose the polycarb due to its higher strength and ability for be cold formed. Acrylic has a harder surface and resists scratches and hazing better. Washing a polycarb windshield with soap and water will help...
  20. harringtondav

    Star Craft Acrylic windshield replacement

    I think you may be able to replace with Lexan/polycarb. My pal has a large BlueWater Coastal Cruiser. His beam much wider than yours, but his windshield was a two piece assembly. I took of a section and traced it on a large piece of paper. ...computer drafting plotter paper works, but you can...
Top