Search results

  1. C

    wires for trim switch merc.

    As most,my trim guage does not work on my merc.o/d because the wires coroded off of the bellhousing. Should I cut the wires behind the motor to stop the stray flow of current that may be coming from the non functioning trim switch on the bellhousing??? Charlie
  2. C

    WOT on 84 evinrude 115 ????

    I recently bought a 17ft. Mako with a 115 evinrude 1984.It runs great and the compression is great.I think it may have the wrong prop on it because it takes a little while to get on plane and then goes like a rocket and runs at about 4200 rpm but has way more left to go,over 5000 I would say.At...
  3. C

    head,holding tank odor

    I am getting a foul odor from my head set-up.Pump flush bowl,holding tank,macerator.The boat is new to me and I pumped out the tank and filled with bleach and ran through the system.I let it set for about 15 minutes and flushed with fresh water and have not used it since.I get an odor when it is...
  4. C

    5.0 lx mercruisers exhaust question

    I noticed that one of my outdrives had significantly more exhaust bubbles than the other.I just had all bellows replaced on both.The one with less exhaust bubbles runs at a slightly higher temp.Any thoughts will be appreciated.
  5. C

    cleaning sunbrella top

    I have a 2 year old navy top and I have the same black run streaks that you get on your hull after it rains on it.I have tried cleaning it with mild cleaner and some bleach with no effect at all.The color is gray and the light color shows everything.Anybody have any luck with this before???Charlie
  6. C

    Lowrance transducer mounting

    Hi guys,my "NEW" used boat has a lowrance depthfinder 3800 model.It keeps showing .5 ft and thats it .When I traced the transducer it was just hanging in the bilge.Is there a way to mount it in the bilge????I have always had transom mount and with the boat in the water for the season I wont be...
  7. C

    Twin 5.0 mercr 1 runs warmer than other

    My 280 Regal has twin 5.0lx with alphas.The starboard motor was running a little warmer than the port.Since this boat is new to me I figured instead of trouble shooting,i would just replace everything cooling related.New manifolds,risers,circulator pump,and o/d waterpump.No change!! It still...
  8. C

    Temp. rises at high rpm on evinrude

    Hi Guys,I have an evinrude 115hp 1984 that runs great.I just replaced the impeller as prev.maint. I have always noticed that when I run at high rpms the temp slowly rises to where I get uncomfortable and I usually pull back on the throttle a little and it comes slowly back down.I was going to...
  9. C

    mercruiser cable adjustment

    I just had all new bellows and shiftcable installed and I need a slight adjustment.It goes into forward fine,but it does not go into reverse easily.there is too much klunking before it goes in and I am a pretty good shifter as far as not shifting too slowly.I cant recall how to adjust the...
  10. C

    need a suggestion to plug a hose temporarily

    I want to clean a water fill hose by filling it with bleach.I would replace it but I cant unsnake it through the boat.I need to temporarily plug one end while I fill the other end with bleach.It is about 2" and I cant think of what to plug the end with.Any suggestions???Charlie
  11. C

    half stripped anchor bolt,need advise

    My anchor bolt at the base of my trim cylinders on my mercruiser has lost most of its threads to corrosion.I just found this out and I am launching this week.The nut tightens but not all the way.I am going to use a temporary fix like marine tex on the end of the bolt so the nut will not back off...
  12. C

    Corrosion on merc bellhousing

    Hi guys,I am new to the forum and hope I can get some suggestions.I saw a similar posting with no replies.I cant get an anchor pin on my bellhousing to move at all.I want to replace it because of corrosion.I will try repeated applications of wd40 first and will welcome any suggestions.Thanks in...
View older results
Top