Search results

  1. jakedaawg

    Help with value of used motor

    I was recently given an old pontoon with a E28ELCED. This is an 89 28SPL with out power tilt, no tiller, with remote control. The toon is only good for scrap. *I am not trying to sell it through this site and will not entertain any offers through this site as I don't want to break the rules.*...
  2. jakedaawg

    Warning horn system brain fart E40TELEDS

    E40TELEDS Side mount controls with the buzzer inside the remote control. Warning intermittently horn stays on solid. Does this regardless of wether engine is running or not. Everything has been checked, actual temps, wireing harness, key switch, checked for faulty sensor (I think, see...
  3. jakedaawg

    VP DP prop wrench for sale here?

    Do they sell the big socket for duo-props on this site? I have such a hard time finding things some times because I am not computer shopping savy. Anyways, I will buy from here if someone posts the part number.
  4. jakedaawg

    Muffs, who still makes a good pair?

    Years ago I purchased a number of the round style flushing muffs. I broke my last pair the other day. What I am looking for is a round style muff that is made from very soft pliable rubber. This style provides a better seal especially when useing with an anti-freeze pump for certain...
  5. jakedaawg

    Stupid question. 2015 duo prop splines

    So, this is gonna be a dumb question. Are the new duo prop prop shaft splines twisted From the factory? 21766684 DPS-B
  6. jakedaawg

    135 optimax compression check

    I have a 135 opti serial number 1B011305 I have found that it has a broken belt tensioner assembly spring and a worn belt. I want to do a compression test before I replace said parts. Is there any reason why these need to be functioning properly before performing a compression test?
  7. jakedaawg

    70 HP TLRT special tool # help.

    Can someone help me with the part number for the tool set to set the reverse gear? I lost the hard drive that had my Yami manuals on it.
  8. jakedaawg

    Glen Lake, Mi straight line wind boat damage

    we had big winds okay, pics wont post please delete until I figure out posting pics
  9. jakedaawg

    BF50A3LRTA High Idle speed when warmed up.

    So, we have what we believe to be a 2003 BF50A3LRTA. Motor starts and runs fine cold or warmed up. The problem happens after you put it back ito neutral after having run it from a cold start. It idles too high to want to atempt to put it back into gear once the engine is warmed up to normal...
  10. jakedaawg

    Is there a way to "Un-Supercede" part numbers

    So, this may be a little unique. A buddy of mine and I bought the surplus parts stock of a long defunct OMC and Merc dealer from the widow. We ended up with a lot of new-old stock. Problem here is the part numbers no longer match the new computer generated super-ceded numbers. Now, we have...
  11. jakedaawg

    93 5.0L 502APRJVB Exhaust Manifold Fastener Torque

    '93 5.0L Ford 502aprjvb OMC Cobra I dont have the manual for these. If someone has the spare time would you mind looking up the torque specs for the nuts and capscrews for the Exhaust manifolds to Heads please. This one did something I had never seen before, they got the boat so hot that it...
  12. jakedaawg

    "IN" manual vs "II" manual

    I am thinking that I never remembered to purchase the 2011 manuals. Do you think I can get by with a 2012 manual for an e25deliih? Pretty sure its gonna be something stupid simple with this motor.
  13. jakedaawg

    E50pl4ss TNT motor brushes

    So, this is one of my personal motors. E50PL4SS. I probably should just buy a new trim pump motor assembly but at $500 bucks and plenty of time I think I would rather see if I can get another season or two out of it. Does any one know where to get brushes for this? Does anyone know where to...
  14. jakedaawg

    E50PL4SS WOT RPM spec

    My SS set of shop manuals seems to have walked off. If someone has the time could you post WOT RPM spec in case my manuals don't wander back into the shop anytime soon. Thanks and sorry for any inconvenience.
  15. jakedaawg

    J60PL4SN Low fuel pressure no residual

    Indications: Only will spin up to 3000 RPM under load. Doesn't hit rev limiter. Runs smooth. No active faults via 4SDS. All voltage tests within spec. The only time I can get the rev limiter to kick in is in neutral. After initial start up it sometimes stalls on acceleration. Does not...
  16. jakedaawg

    Rinda Diacom Vs. CDI M.E.D.S.

    I need to invest in diagnostic technology. Primarily to be used with Merc outboards and mercruisers. I have BRP software. Has anyone tried either? Pros-Cons?
  17. jakedaawg

    Tool part # help

    I need the part # for the prop shaft bearing carrier removal tool. This would be a sleeve with three prongs. It is for a 15hp merc serial # oc193225 Thanks in advance
  18. jakedaawg

    Pontoon Carpet weights

    I am going to re-deck and replace the carpet for a customer. I want to use premium carpet, not concerned about price. Does anyone know what weight carpet is used on the luxury pontoons? The benningtons and premiers and such.
  19. jakedaawg

    need tips for finding an old "tower of trouble"

    So, buddy of mine and I picked up an old sidewinder. Gonna be a project boat. He is an old merc race team driver so I want to suprise him with a black engine for the boat. If I remember correctly they used to make a tower of trouble in the 135-150 HP range. I have been searching for one. I...
  20. jakedaawg

    Test complete, thanks, you can delete if you need to.

    http://s1276.photobucket.com/user/mo...herun/library/ Please tell me if this link works. I am trying to learn to use PB to post photos.
Top