Search results

  1. R

    Idle Issues - 1980 Johnson 115 - J115TLCSA

    Post the actual compression values here.----Does spark jump a gap of 3/8" on each lead using a proper test device?----Are the model #'s the same on the 1980 and 1995 model as you posted ??----The electric primer is a valve , it is not a pump.----Replace water pump impeller or at least test the...
  2. R

    Nosing down

    If tilt pin is in the hole closest to the transom , move it away by 2 holes.-----Test run.
  3. R

    1978 Evinrude 140hp flooding after running

    Spend no beer tokens until you determine condition of the outboard.----If all is well install a new impeller.----New diaphragm in fuel pump.----Make sure carburetor jets are clean.----You need a top notch / tested battery.-----Might as well take starter apart for inspection / cleaning.----Do an...
  4. R

    1978 Evinrude 140hp flooding after running

    The first thing to do is a compression test on this 47 year old crossflow.----Post the actual values here.
  5. R

    Cowl years that would fit a 1966 18HP Evinrude Fastwin 18602C

    You would need a cylinder head , lower cowling and other brackets to make that 50's cowling fit.
  6. R

    What HP?

    Depends on condition of the boat.----Could be water logged.-----Depends on what you want for maximum speed.
  7. R

    1987 mercury 45hp classic 50 shut off in the middle of running

    Yes , these motors have a switch box.
  8. R

    Just keeps going right

    If boat pulls to the right, swing trim tab to the right.
  9. R

    120 hp Johnson starter won't connect with flywheel

    No geared down starter on that 1989 model 90 degree looper.----Does the starter motor turn counterclockwise when looking down on the starter , yes or no ?
  10. R

    Boat will run perfect in neutral and will rev up in neutral but will die instantly

    It only " sounds " perfect in neutral to you.-----There is no load on it.
  11. R

    What should I offer on this outboard?

    Can you work on this motor yourself ?----Do you have a local boat shop that will work on it now and a few years from now?
  12. R

    120 hp Johnson starter won't connect with flywheel

    The MODEL number must be posted !----Numbers posted so far are no help at all.-----Or pictures of motor cowling and motor power head needed.-----You are sure battery is hooked up correctly?----You are sure that starter is assembled correctly?-----Did you see the motor run when you bought the...
  13. R

    Hello all I just got this Evinrude 88 SPL for free from a friend cranks no start no idea how to work on boats but willing to learn

    You would have to turn the key to " on " and safety lanyard clip installed if control has that.
  14. R

    1953 Goodyear Seabee 12hp issues.

    Does spark jump a gap of at least 1/4" on a test device?-----Checked for cracked ignition coils ?----Post a few pictures of this motor.
  15. R

    1953 Goodyear Seabee 12hp issues.

    What do you mean by ----" the strongest water pump I've seen " on this motor.-----Pull the flywheel and see if coils are rubbing against magnets.-----Check and see if magplate bushing is loose / worn.----How did you adjust the timing on this motor ?
  16. R

    120 hp Johnson starter won't connect with flywheel

    I do not believe the 120 models were ever marketed with the 60 degree looper block.--The small 60 degree blocks had the gear down starter.----Load test the battery.----Take starter apart for cleaning , inspection , ohm check on armature.----No beer tokens spent to do this.-----Perhaps new...
  17. R

    Hello all I just got this Evinrude 88 SPL for free from a friend cranks no start no idea how to work on boats but willing to learn

    If water got inside the engine , it needs to come apart for inspection.-----Take starter apart for inspection and ohm test on armature.----Do a compression test using rope on the flywheel.
  18. R

    120 hp Johnson starter won't connect with flywheel

    I doubt the 120 has that gear reduction starter !
  19. R

    70HP Johnson 2-stroke hunting at WOT

    It should be running at 5000 / 5500 RPM at full throttle.-----Post actual compression values.----Does spark jump a gap of 3/8" on each lead ?-----Stop running the motor as it is now.-----A plugged carburetor can result in serious piston / cylinder damage.
  20. R

    Trying to find out what engine - Need help

    It is a G in your serial # and NOT a 6
Top