Search results

  1. alldodge

    Outboard MARINER 75 ELPTO wont start

    Pics are not working. Would need to upload pic at another location and link here
  2. alldodge

    Don't see fuel in jets

    No Fuel will only come up to carb when motor is cranking. Disconnect fuel line at carb, place end of line in something that will catch the fuel and crank the motor
  3. alldodge

    Crank driven vs block mounted raw water pump pros/cons

    By no means am I an expert with thru hull placement, but with this being for the motor my main concern is the hull light and fast enough to bring it out of the water where the intake would get air. Most fast boat use things like THIS I also don't like plastic for motor water intakes, unless...
  4. alldodge

    Don't see fuel in jets

    Thanks Your correct mechanical fuel pump Motor Removed my previous post to clean up the thread
  5. alldodge

    Outboard MARINER 75 ELPTO wont start

    As muc mentioned a voltmeter would be best to determine fault Your saying you want to bypass the neutral safety switch?
  6. alldodge

    Ballast Resistor versus 8-9V on positive Coil

    yes
  7. alldodge

    Don't see fuel in jets

    Good point, I saw GLP-E and thought GL-E What size motor is this?
  8. alldodge

    Red Pipe Sealant on T Connections etc on the block/manifolds?

    Either Mercury Perfect seal if you can find it, or Permatex 80019 (Aviation Sealant form a gasket)
  9. alldodge

    Ballast Resistor versus 8-9V on positive Coil

    Manual 2 on pg 8A-7 list resistance wire should be 1.8-2.0 ohms so 4.0 to 5.0 amps depending on if there is 8 to 9V 1.8 ohm
  10. alldodge

    Mechanical things hate me lately

    Might also need a caliper rebuild or replace or slide pins/parts binding
  11. alldodge

    Knocking when turning

    The drive went on just fine but found out it knocks on hard turns Removed drive, drove gimbal bearing further in and now drive won't go back on. The drive shaft is not making it into the engine coupler. The coupler teeth are damaged, the coupler is warped/damaged or the gimbal bearing is...
  12. alldodge

    New Stuff on Vehicles likes/dislikes

    On the front, wife's XT5 has them behind the wheel. Design is similar to F1 race cars
  13. alldodge

    Knocking when turning

  14. alldodge

    MerCruiser Engine (replaced 2019) RPMs Drop After 50 minutes

    Welcome Moved your thread to the Mercruiser section so it will get more views, and don't see a Regal 4260 having outboards How about let us know what motor are you discussing and motor serial numbers are best
  15. alldodge

    Knocking when turning

    New gimbal bearings are stiff. Put alignment bar in and make sure it goes all the way in. Smack the bar hard with your hands, up/down/left/right a few times.
  16. alldodge

    5.7 Switched 12v

    Just guessing but most EFI are 650 to 700
  17. alldodge

    I/O (Sterndrive) Conversion to Outboards

    Merc Easier to find someone that does work on them Verado has good track record Tariff cost should be less
  18. alldodge

    Bait and Livewell

    Hey @dingbat have an idea?
  19. alldodge

    ZF 63 IV water in oil

    Suggest using diesel to flush Don't know of a way to pre-test prior to install. Could take it apart and inspect, maybe another has a better idea
  20. alldodge

    New Stuff on Vehicles likes/dislikes

    My 21folding mirrors still worked when traded, new 25 has folding power extending. Think I'm going to like the extending, been many times I hook up the boat and start driving the do the Homer Simpson because 21 had manual extend
Top