Search results

  1. alldodge

    Problems starting after fuel filter/water separator change

    Use a voltmeter and see if 12V is at the coil pink/white wire with key ON
  2. alldodge

    Problems starting after fuel filter/water separator change

    Did the kill switch get tripped?
  3. alldodge

    thunderbolt ignition blows fuse after start

    Welcome Leaving key on for days might have over heated the coil. Disconnect the + side wire and see if it still blows
  4. alldodge

    On crank no fuel to throttle body mercruiser 305 EFI

    No, it's the module inside the Dizzy Looking at your pic I'm only seeing 2 wires
  5. alldodge

    On crank no fuel to throttle body mercruiser 305 EFI

    It's almost never the coil Most cases it's a bad connection or the old style module. The old modules had grounding problems, so Merc went from to 2 wire to a 3 wire module. The 3rd wire was a ground wire. Do you have 2 or 3 wires coming out of the dizzy?
  6. alldodge

    I have to do a gimbal bearing and bellows etc, I have a question regarding the shift cable. Merc A1 G1 3.0

    And just why are you responding to me? Why not respond to the OP He asked?
  7. alldodge

    I have to do a gimbal bearing and bellows etc, I have a question regarding the shift cable. Merc A1 G1 3.0

    This works but assumes your replacing the lower cable so you have one to cut
  8. alldodge

    On crank no fuel to throttle body mercruiser 305 EFI

    Your motor breakdown
  9. alldodge

    On crank no fuel to throttle body mercruiser 305 EFI

    Welcome Most likely we will need your motor serial number, but until then Looks like TBV distributor So it will not start on it's own but if it's given a shot of starting fluid it will continue to run? Measure voltage at the Battery and then at the coil. Is both the Bat voltage and coil...
  10. alldodge

    1992 Nissan NS90A alarm at low speed, Dies above 3/4 Throttle

    Welcome Never worked on a Nissan but your getting an alarm and then the motor starts to die. Need to do some testing Did find that the Nissan is actually a Tohatsu just rebaged Crank slow can come from a weak battery, bad connections or the motor is over heating. Take a IR temp gun and measure...
  11. alldodge

    Merc 115 4 strokes 2001 ECU/fuel pump problem

    Have you tried replacing the relay, check clean and tighten contacts on relay? Merc ECM's apply a ground to one side of the relay coil. When ground is applied the relay energizes and makes contact across 85 to 30 to power the FP The pic below is not your motor but how the FP relay is powered...
  12. alldodge

    Throttle movement but no increase in engine rpms

    I stand corrected, old medium and small outboards used less than inch pitch and currently high end Rev4 and Enertia Eco XP using special alloys Question, other than a Bravo 2 who has ever put a 18 inch diameter prop on a Alpha or Bravo drive?
  13. alldodge

    I have to do a gimbal bearing and bellows etc, I have a question regarding the shift cable. Merc A1 G1 3.0

    Scratch that no need to remove Detach, loosed shift cable bellows and pull it out some. Might attach a string to end in case it's pulled somewhere hard to get at edit: won't be able to replace shift bellows this way
  14. alldodge

    Throttle movement but no increase in engine rpms

    Not everyone knows or even does that, also never heard of anything other than solid numbers for pitch
  15. alldodge

    I have to do a gimbal bearing and bellows etc, I have a question regarding the shift cable. Merc A1 G1 3.0

    Yes and No Yes, disconnect then loosen 2 screws on end of wire anchor then remove plastic guide
  16. alldodge

    Throttle movement but no increase in engine rpms

    That's the diameter, pitch is 18
  17. alldodge

    Throttle movement but no increase in engine rpms

    This doesn't add up, 4 blade aluminum to 4 blade stainless and same pitch. Maybe if the aluminum was damaged
  18. alldodge

    4.3gxi bad temp sensor?

    Good point, have motor running
  19. alldodge

    4.3gxi bad temp sensor?

    Motor of voltage for TPS looks good, MAP is a bit low, should be closer to 4.9 but 5V ref is a tad low Once started the MAP should be around 1.4v With IAC counts so high there is to much air for the fuel. Might move the bad running ECM to the good motor. Don't move the good to the bad,
  20. alldodge

    Rear water port near deck

    My guess is the boat use to be in salt water and that is a fresh water flush port. It's probably missing a cap
Top