Search results

  1. Lou C

    Need some info on adapting a Sierra A1 marine fuel line to a Carter mechanical fuel pump

    https://michiganmotorz.com/fuel-line-hose-3-8-fuel-pump-to-carburetor-31-length/?searchid=60520&search_query=sierra+fuel+hose they seem to use this on their carbed turn key engines... the right angle end threads right into the Edelbrock fuel inlet, the fitting on the end for the pump is the same...
  2. Lou C

    If you're wondering if your anti siphon valve is stuck, or clogged, here's a test....

    BTW they make anti siphon valves out of both aluminum and brass, the brass ones are more expensive but are likely to last longer esp in salt water...
  3. Lou C

    Need some info on adapting a Sierra A1 marine fuel line to a Carter mechanical fuel pump

    OK got a question about using a Sierra A1 flex fuel line (this is if I wind up converting from my Quadrajet to an Edelbrock in the future), this Sierra line has brass fittings that appear to be 5/8ths" but the threads in the fuel pump are 1/2". At the carb end the Sierra threads right into the...
  4. Lou C

    Omc outdrive knocking noise while cruising.

    I recall reading about the recall on the Cobra lower gears, what they also found was that a supplier changed the spec on the lower shift cable, they had too much drag and were causing the drive to not shift fully into gear and that rounded off the clutch dogs/lower gears. The new cables were red...
  5. Lou C

    Cars you should have kept.

    our family had a 1970 Ford Torino 2 door with the 302 and 3 spd auto also a 1972 Chevy Impala with a 350 and 3 speed auto next a 1975 Olds Delta 88 with the same powertrain but that one had a Quadrajet 4bbl Last new car my parents had was a 1992 Ford Crown Victoria, looked like a police cruiser...
  6. Lou C

    Cars you should have kept.

    I’d love to build another. With what’s available today you can build a far superior Buggy!
  7. Lou C

    Cars you should have kept.

    Not a collectible but wish I still had: Fiberfab Dune Buggy built off a 1956 VW, with a 1200 cc 40 hp engine lol 1989 Toyota Corolla GTS sport coupe it had the same 1600 cc twin cam engine as the MR2. Fast and fun.
  8. Lou C

    5.0GXi Starter Replacement

    When you use their bolts you’re pretty much guaranteed that they won’t be too long and bottom out, which can allow the starter to move. The issue is that there are many manufacturers making after market starters to fit Chevrolet marine engines and the dimensions of the starter case can be...
  9. Lou C

    Ford 302 engine oil dipstick - 1995 OMC Cobra, Ford 302, VolvoSX

    It looks like the 5.0 & 5.8 Fords were used by OMC from 1989 to 1996. Not sure if Volvo did the same….
  10. Lou C

    Ford 302 engine oil dipstick - 1995 OMC Cobra, Ford 302, VolvoSX

    Hard to say I wonder if you could put out this question to forum members that have OMC/Volvo Ford engines in that age range. If you look at that catalog link I posted you can check to see how many model years that part number was used on the Ford 5.0 V8.
  11. Lou C

    Ford 302 engine oil dipstick - 1995 OMC Cobra, Ford 302, VolvoSX

    https://www.marineengine.com/parts/omc-parts/omc-boat-parts.php?year=1995&hp=5.0&model=502APHUB&manufacturer=OMC+stern+drive&section=Oil+Pan+%26amp%3B+Oil+Pump based on the part number here it looks like you have the right dip stick, but don't know why it has both the dimples and hash marks I'd...
  12. Lou C

    5.0GXi Starter Replacement

    Hmm not sure, I have never used it and had a few different starters in my engine over the years and never had a loose starter bolt, nor did I have one that wouldn't come out.
  13. Lou C

    Ford 302 engine oil dipstick - 1995 OMC Cobra, Ford 302, VolvoSX

    I'm wondering since OMC/Volvo used both GM and Ford engines, if they used the same dipstick and different markings on both, you could figure that out by checking part #s. I have a similar system on my '88 4.3, but it just has the hash marks no dimples that I've noticed but next time I'm at the...
  14. Lou C

    New Stuff on Vehicles likes/dislikes

    Gateways that require you to pay extra to run a scan like on Stellantis vehicles 2019 & up. You pay for the scanner, then pay for the subscription for it, then to get past the gateway!
  15. Lou C

    5.0GXi Starter Replacement

    Knurling keeps it from getting loose; yes it’s tough to get a torque wrench in there but when you have been doing this for a long time you just can feel it. Not bubba tight but tight. Loose starter bolts will allow the starter to shift under torque and can break the bolts leading to grief!
  16. Lou C

    Engine, Carb or Prop? need suggestions or ideas please.

    Did you check the tension on the secondary air door spring? That’s a major source of Quadrajet bog, those secondary air doors opening too soon… May need to tighten it up….remember on these carbs the actual secondary blades are mechanically operated but no air gets sucked in till the air doors...
  17. Lou C

    Erratic tachomether

    I might want to hook up a voltmeter to your I terminal (Ignition) on the switch and see what voltage it’s getting when the tach acts up. Also some OMCs have high resistance in the charging sense circuit and this can cause overcharging at the battery yet you may see low voltage read out on the...
  18. Lou C

    2003 Glastron VP 5.0 GL Overheat issue

    Excellent glad you got it back together & alls well!
  19. Lou C

    Volvo Penta 5.7 GXI Fuel in Oil Runs smooth at idle

    Agreed it doesn’t make sense; id be thinking of doing an air pressure test of the cooling passages to see if they hold pressure….
  20. Lou C

    I should add a 2nd battery...

    I've been getting 7 years average from the lead acid GP 27 dual purpose batteries I use. My boat is covered but of course some water always gets in and I have never had a dead battery from whatever time the bilge pump has to run.
Top