Search results

  1. Scott06

    Need Air Compressor Help

    This wont be getting full voltage to motor downstream of pressure switch. Plugging it in to multiple outlets wont fix that
  2. Scott06

    Chainsaw cutting lube in a pinch

    Had a vet recommend the same to get heating oil out of dog fur ... worked very well at 11 pm on a sunday night... although he recommended Palmolive. given the amount of time on this thread the OP could have driven to any gas station for motor oil
  3. Scott06

    Closed Cooling System Part # 860234A1

    Why dont you post a pic of the engine and bracket where it is hitting the belt. Wonder if belt is on wrong or if someone added the seawater pump separate. Is the engine an alpha model originally as you list both alpha/bravo above ?
  4. Scott06

    What does this marking mean on this new to me outdrive?

    He is just being a wise azz... Did you ask the guy you bought it from.... Yes most likely customer name so they can put it back on a boat in the spring, which must not have happened... Did it pass a pressure test?
  5. Scott06

    Bought a Used Boat, but what is it?

    What is it - probably a bucket of chit. The more you stir it up the more it will stink. I think by the time you check the stringers, transom, and floors for rot you will wish you left it where it was sitting. As others have eluded it is a really obsolete engine and drive combo. Yes the engine...
  6. Scott06

    Mercruiser 5.7 with V6-14 TB IV module??

    Check the kill / Man overboard switch. ignition gets power off starter when cranking then switches over to purple wire when in run. Can verify by putting key in run, check for 12 v at coil positive terminal
  7. Scott06

    Mercruiser 5.7 with V6-14 TB IV module??

    if it worked before you pulled the dist most likely is it is mis timed. The V6 module will work fine to run And you don’t have to advance it more than your normal 10 degrees initial to get it to start. It will not give as much total advance but you can worry about that later. I tested my engine...
  8. Scott06

    Can't remove 5.7 vertically.

    Nice whats under the hood of the chevy?
  9. Scott06

    Can't remove 5.7 vertically.

    Nice. The only thing I may suggest- something to make sure the chain can't slide off the end if the engine gets hung up on something
  10. Scott06

    Sea Water Pump Cover - Question

    Best to search on this site by serial number but I think 13 is waht u are looking for https://www.marineengine.com/parts/mercruiser-sterndrive-parts/350-mag-ski-gm-350-v8-19911996/0d505450-thru-0k040399/sea-water-pump-assembly
  11. Scott06

    help with engine block swap

    The two piece uses this coupler That bolts to crank hub https://www.michiganmotorz.com/mercruiser-hub-style-coupler-1985-earlier other diffs are the starter bolt pattern. I believe your original engine will use a 14” flywheel with staggered pattern , replacement engine will use the 12 5/8”...
  12. Scott06

    9670 Carb question

    Are you looking to rebuild or replace the carb. If looking to replace vs rebuild i belive an edlebrock 1409 would be a drop in replacement
  13. Scott06

    4.3 Replacing exhaust manifolds - ditch nylon drain plugs?

    Have not had an issue with mine but replace the plugs every couple years. If you feel better replace them or upgrade to brass pipe thread fittings. You don’t neccesaarily need a drain plug can remove hose to winterize
  14. Scott06

    VP 4.3 GL conversion to Holley Sniper 2 efi

    That is the same one I got worked perfectly. Not sure if the kit is same as Holley but doesn’t list volvo carbs to keep yiu from buying non VP parts …
  15. Scott06

    VP 4.3 GL conversion to Holley Sniper 2 efi

    I ended up with the VP kit for same reason as op, couldn’t find a kit that matched the carb number. Mikes could only give me a probably should work about their kit. the VP kit was only $25 more than mikes kit so worth it if not one can guarantee fit. i think I got if from Leaders RPM in michigan.
  16. Scott06

    VP 4.3 GL conversion to Holley Sniper 2 efi

    based on your symptoms yes start with carb rebuild. would also get a new float. Last summer i did the holley 2 bbl on my buddies 4.3 VP. Starts and runs perfect now. I found an oem VP kit for less than $100. I got the float at mikes carb, they also have good how to vids. The idea to replace...
  17. Scott06

    VP 4.3 GL conversion to Holley Sniper 2 efi

    I think there was a guy on here doing sniper to his Mercruiser 3.7 or may have been Marine engine forum. You can type sniper in the search and get all the threads where guys have done it... I think the issue the guy may have hit was coolant temp. You want to verify this in case I am talking...
  18. Scott06

    Mercruiser 4.3 MPI 2010 Connectors...

    Would look to get a wiring diagram for it. I may have one electronically will look this evening. It is not uncommon for fins some unused connections in your harness. I had an extra ground or two that had never been terminated. does the connector next to the distributor in first pic fit the...
  19. Scott06

    305 boat cam

    @Scott Danforth can probably recommend a cam if you really want to spend for a roller. Would also recommend the Edelbrock 1409. Not to spend your money, but it is easier than spending mine.... what would be worth it if you haven't done the machine work on the heads is get a set of vortec...
  20. Scott06

    2001 Maxum 2400 sc for 13k v 1995 FourWinns 238 vista

    Have you priced upholstery work? I had my sunpad redone 2 years ago was almost a grand and took 3 months. Have you checked any wood structure like transom and stringers for rot? All other things being equal unless you can do the upholstery work I'd do the maxum as you will be close to same...
Top