Search results

  1. Scott06

    BRAVO 3 RATIO

    Ok the problem is a little more complex... I am not the right person to SWAG a ratio for your application. Maybe @alldodge can help? SEI just started making aftermarket B3's https://www.sterndrive.cc/Mercruiser-Bravo-Applications.html It may be worth diagnosing your current drive if only to...
  2. Scott06

    Winterize carb

    to be blunt sounds like a dumb way to get gas treatment in the carb... put it in the tank so it gets mixed and run it on the way to pull it out at end of year ( or on the trailer). Has worked for me for 30 years on both E10 and non ethanol. Boat I get non ethanol dock side jetski I fill up cans...
  3. Scott06

    Winterize carb

    I add stabil to the tank before last run of season. Never had an issue with non ethanol or E10 doing this.
  4. Scott06

    BRAVO 3 RATIO

    You mean it would not bolt up or the rpms were wrong? If rpms at wot what did you get ? you maybe able change out props or re gear your existing drive
  5. Scott06

    Can't remove 5.7 vertically.

    Doesnt make it any easier for the OP, but if you have done rigging or industrial maintenance work its not an issue. In a perfect world yes the dog house would come off but 99 % of boat owners never have to remove the engine.
  6. Scott06

    Can't remove 5.7 vertically.

    Exactly same back in a little muscling around should come out ok
  7. Scott06

    Can't remove 5.7 vertically.

    somebody has a sense of humor. Can you take a shot looking inside the engine compartment? How much height above the engine? Thinking a beam with a trolley on it slide engine forward then angle up like going over the core support pulling the engine out of a RWD car ? Either that or Sawzall and...
  8. Scott06

    Torqe for impeller housing in 3.0 merc i/o

    it only goes down far enough to seat the oring, also the top of it supports the wear plate under the impeller so it should be even with the top of housing where the plate sits. The manual tells you not to drive it in but I had to tap mine down to get it in. Lubing the oring helps Manual #14...
  9. Scott06

    Torqe for impeller housing in 3.0 merc i/o

    two phillips screwdrivers in the holes partway up the cone. They will lever it out. Important to change that since it must have gotten hot. Did the impeller pieces get into cooling system? Hopefully you are using merc parts - some of the aftermarket impellers are junk. I think in the stickies...
  10. Scott06

    Torqe for impeller housing in 3.0 merc i/o

    its like 15 inch pounds. or snug with a 1/4" ratchet and calibrated elbow... never used a torque wrench on it. I have never used sealant on the gaskets, but some use perfect seal/Permatex #3, which wont hurt pay attention to the order and holes being in correct orientation. If you are gonna...
  11. Scott06

    2006 DP-SM with Clicking Under Load

    Exactly I just went through this on my alpha gen 2 u joints felt smooth by hand when I took them out two caps on each had rough spots on the cross and cap. I had felt a vibration when trimming in under load.
  12. Scott06

    What size prop and pitch

    I this
  13. Scott06

    Tilt/trim pump

    After you clean all the connections if it is still happening trouble shoot the solenoids or relays. You can swap the up one for down and see if the issue follows.
  14. Scott06

    Help to source Bravo 3 gimbal housing

    I usually have luck putting in a search on ebay...
  15. Scott06

    Would you?

    Absolutely. I dont think it would be great or safe on the highway. But I would not give the 4 mi trip a second thought unless the trailer brakes were non functional. Used to do similar trip with my dads 22 ft Catalina sailboat towed by a 98 Accord 2 dr V6. Looked goofy with the larger hull...
  16. Scott06

    Marine grease for gimball bearing

    Lucas Marine is fine , as is their red and tacky. Used in my gimbal for last 20 years
  17. Scott06

    Clutch Hydraulics, 1989 GMC C1500

    You rebled the master or replaced the master again? Only other thing that may be influencing it is if the pilot bearing. If they get worn they can drag a bit or a lot. I think of the time this issue shows up at slow speed or parking
  18. Scott06

    Anyone put a tower on a Regal Ventura 8.3?

    Ok that makes sense. Not sure your budget you can spend a bunch for a custom fit tower like New Dimension https://www.newdimensiontowers.com/biminis these are custom built to your boat model and oem quality. The krypt tow worked great fro me but doesn’t look perfect as the side rails don’t fit...
  19. Scott06

    Anyone put a tower on a Regal Ventura 8.3?

    Not sure if you got any answers and no havent put a tower on that exact boat. I put this Krypt tower on my Sea Ray - was relatively easy and affordable. I was pleasantly surprised with how quiet this tower is when I got it on the boat...
  20. Scott06

    Bearing SKF #

    On my merc alpha I tore it down and got the numbers off the bearings and races. Some merc bearings were similar price to the same SKF or Timken bearing from a bearing house, some were x2 price. I still don’t understand why the u joints are so expensive. My alpha gen 2 uses GKN ujoints, when you...
Top